Документ взят из кэша поисковой машины. Адрес оригинального документа : http://www.atnf.csiro.au/pub/people/vlbi/vt02/vt02f/vt02f8/sched.runlog Дата изменения: Tue Mar 7 04:51:32 2006 Дата индексирования: Mon Jun 28 00:05:33 2010 Кодировка: Поисковые слова: http astrokuban.info astrokuban

Welcome to program SCHED. Version: 6.02 July 2005

The manual is at http://www.aoc.nrao.edu/~cwalker/sched/sched/sched.html
Unix users should set $SCHED to the base area where SCHED is installed.
Most run time messages will be in sched.runlog

Some useful commands to give now if running interactively:
SCHedule= : Specify input file.
PLOT : Invokes uv, xy, rd, and uptime plotting.
FREQLIST=lowF,highF : Make frequency list (MHz). Then exit.
EXIT : Leave program.
/ : End of inputs - run program (or EXIT).

TPINI: Reading tape initialization information from SCHED input file.
SRREAD: Reading source catalog: Program_input
SRREAD: Please convert source catalog from use of EPOCH to EQUINOX.
RDSET: Reading setup file: oh.set
STREAD: Reading station catalog: /nfs/atapplic/vlbi/sched/catalogs/stations.dat
STREAD: Will read locations file /nfs/atapplic/vlbi/sched/catalogs/locations.dat
SCHIN: Found 2 input scans.
CHKCODE: EXPCODE = vt02f8

WRTMSG: Special message from routine CHKCODE:

======================================================================
WARNING The project code (EXPCODE) for this observation has a
non-standard format. Valid codes start with one or two
letters followed by 3 digits. Any leading zeros should
be included. A couple of valid examples are bt068
and v003.

Note that some SCHED examples use non-valid codes, as do
VLBA test observations.
======================================================================


GETFREQ: Reading frequency file: /nfs/atapplic/vlbi/sched/catalogs/freq.dat
SHORTN: WARNING - Source names longer than 8 characters used.
Mark III correlators and geodetic software will have problems.
SCHOPT: First output scan will be number 1
SCHOPT: There will be 2 output scans ( 1 - 2) from 73/13:00:00 to 73/14:05:00
SUMOPE: Writing summary file vt02f8.sum
OMSOUT: Writing OMS file vt02f8.oms
VXWRT : Writing V E X file vt02f8.skd
VXWRIF: WARNING, Phase cal not under computer control for some stations.
Contact stations by e-mail to make sure phase cal is switched off
VXS2MD: S2 Modes with DAR = NONE wiring not implemented, using naive S2 mode
VXWRTR: WARNING, un-documented S2_data_source, may not be recognized by PCFS

Scan number: 2
Start time: 2006-073-13:55:00
Stop time: 2006-073-14:05:00
Source: 340.054-0.24
Station codes: At,Mp,Ho,Pa
Setup file: oh.set
PRTSCN: Scan information was written to the log file.
VXSCHK: WARNING: Mode setup < 40s for station ATCA
Stations need 40s for any mode change, incl frequency shift.

Scan number: 2
Start time: 2006-073-13:55:00
Stop time: 2006-073-14:05:00
Source: 340.054-0.24
Station codes: At,Mp,Ho,Pa
Setup file: oh.set
PRTSCN: Scan information was written to the log file.
VXSCHK: WARNING: Mode setup < 40s for station MOPRA
Stations need 40s for any mode change, incl frequency shift.

Scan number: 2
Start time: 2006-073-13:55:00
Stop time: 2006-073-14:05:00
Source: 340.054-0.24
Station codes: At,Mp,Ho,Pa
Setup file: oh.set
PRTSCN: Scan information was written to the log file.
VXSCHK: WARNING: Mode setup < 40s for station HOBART
Stations need 40s for any mode change, incl frequency shift.

Scan number: 2
Start time: 2006-073-13:55:00
Stop time: 2006-073-14:05:00
Source: 340.054-0.24
Station codes: At,Mp,Ho,Pa
Setup file: oh.set
PRTSCN: Scan information was written to the log file.
VXSCHK: WARNING: Mode setup < 40s for station PARKES
Stations need 40s for any mode change, incl frequency shift.
VXSCH: Tsys calibration is taken during every gap in recording, but these appear over 15 min apart!
This can be improved by inserting 40 second gaps at regular intervals.
VXSCH: WARNING: Scan timing problem for PCFS, this VEX will NOT run!!!!
FLAGS: Writing apriori flagging file vt02f8.flag
Processing ATCA
Processing MOPRA
Processing HOBART
Processing PARKES