Äîêóìåíò âçÿò èç êýøà ïîèñêîâîé ìàøèíû. Àäðåñ îðèãèíàëüíîãî äîêóìåíòà : http://www.naic.edu/~phil/td/PK2200UM.pdf Äàòà èçìåíåíèÿ: Tue Aug 17 19:17:38 2010 Äàòà èíäåêñèðîâàíèÿ: Tue Oct 2 01:00:15 2012 Êîäèðîâêà: Ïîèñêîâûå ñëîâà: http www.astronomy.ru forum index.php topic 4644.0.html

PK2200 Series
C-Programmable Controllers

User 's Manual
019­0015 · 071126­F


PK2200 User 's Manual
Part Number 019-0015 · 071126-F · Printed in U.S.A. © 1999­2007 Rabbit Semiconductor Inc. · All rights reserved. Rabbit Semiconductor reserves the right to make changes and improvements to its products without providing notice.
No part of the contents of this manual may be reproduced or transmitted in any form or by any means without the express written permission of Rabbit Semiconductor. Permission is granted to make one or more copies as long as the copyright page contained therein is included. These copies of the manuals may not be let or sold for any reason without the express written permission of Rabbit Semiconductor.

Trademarks
· Dynamic C® is a registered trademark of Rabbit Semiconductor Inc. · Windows® is a registered trademark of Microsoft Corporation · PLCBusTM is a trademark of Rabbit Semiconductor Inc.
The latest revision of this manual is available on the Rabbit Semiconductor Web site, www.rabbit.com, for free, unregistered download.

Rabbit Semiconductor Inc.
www.rabbit.com


TABLE
About This Manual Chapter 1: Overview

OF

CONTENTS
vii 11
12 14 15 15 16

Introduction .......................................................................................... Standard Features ................................................................................. Flexibility and Customization Options ................................................ Development Kit .................................................................................. CE Compliance ....................................................................................

Chapter 2: Getting Started

Connecting the PK2200 to a PC .......................................................... 18 Establishing Communication with the PK2200 ................................... 19 Running a Sample Program ................................................................. 20

17

Chapter 3: Subsystems

Subsystem Overview ............................................................................ Processor Core ................................................................................ CPU ............................................................................................ Microprocessor Supervisor/Watchdog Timer ............................. Static RAM ................................................................................. EPROM/Flash EPROM ............................................................. EEPROM ................................................................................... Real Time Clock (RTC) ............................................................. Digital Inputs ................................................................................... Digital Outputs ................................................................................ Serial Communication ..................................................................... Serial Channel Configuration ..................................................... Keypad and Display ........................................................................

21

22 23 23 23 23 23 24 24 24 27 29 29 31

Chapter 4: System Development

Changing Modes .................................................................................. Setting the Mode ............................................................................. Development Options .......................................................................... Memory Options ............................................................................. Battery-Backed RAM ..................................................................... EPROM ........................................................................................... Flash EPROM .................................................................................

33
34 34 35 35 35 36 36

PK2200

Table of Contents s iii


Digital Inputs ....................................................................................... Using the Digital Inputs .................................................................. Interrupt Inputs ................................................................................ High Speed DMA Counter .............................................................. Digital Outputs ..................................................................................... Using the Digital Outputs ................................................................ Serial Communication .......................................................................... Receive and Transmit Buffers ......................................................... Echo Option .................................................................................... CTS/RTS Control ............................................................................ XMODEM File Transfer ................................................................. Modem Communication .................................................................. Interrupt Handling for Z180 Port 0 ................................................. Remote Downloading ...................................................................... Developing an RS-485 Network ..................................................... Keypad and LCD ................................................................................. Using the Keypad and Display ........................................................ PK2200 Keypads ............................................................................ Keypad Insert Templates ............................................................ Keypad Codes ............................................................................ PK2200 LCDs ................................................................................. Graphic LCD Status ................................................................... Bitmapped Graphics ...................................................................

36 36 36 36 37 37 38 38 39 39 39 39 41 41 42 43 43 43 44 45 46 46 47

Chapter 5: Software Reference

Software Drivers .................................................................................. Real Time Clock (RTC) .................................................................. EEPROM ........................................................................................ Digital Inputs and Outputs ................................................................... Digital Input Drivers ....................................................................... Digital Output Drivers ..................................................................... LCD and Keypad ................................................................................. Sample Programs ................................................................................. Communication Sample Programs .................................................. PK2240 Sample Programs ..............................................................

49

50 50 51 52 52 54 55 62 63 64

Appendix A: Troubleshooting

Out of the Box ...................................................................................... Dynamic C Will Not Start .................................................................... Dynamic C Loses Serial Link .............................................................. PK2200 Repeatedly Resets .................................................................. Common Programming Errors .............................................................

65

66 67 67 67 68

iv s Table of Contents

PK2200


Appendix B: Specifications

General Specifications ......................................................................... Hardware Mechanical Dimensions ...................................................... High Voltage Driver Specifications ..................................................... Environmental Temperature Constraints .............................................. Connectors ........................................................................................... Header Locations and Jumper Settings ................................................

69

70 71 75 75 76 76

Appendix C: Power Management

Power Failure Detection Circuitry ....................................................... 80 Power Failure Sequence of Events ...................................................... 80 Recommended Power Fail Routine ...................................................... 82

79

Appendix D: Interrupt Vectors and I/O Addresses

Interrupt Vectors .................................................................................. Jump Vectors ........................................................................................ EEPROM Addresses ............................................................................ Processor Register Addresses .............................................................. PK2200 Peripheral Addresses .............................................................

85

86 87 88 89 91

Appendix E: PLCBus

PLCBus Overview ............................................................................... 96 Allocation of Devices on the Bus ...................................................... 100 4-Bit Devices ................................................................................ 100 8-Bit Devices ................................................................................ 101 Expansion Bus Software .................................................................... 101

95

Appendix F: Backup Battery

Battery Life and Storage Conditions .................................................. 108 Replacing Soldered Lithium Battery .................................................. 108 Battery Cautions ................................................................................ 109

107

Index

111

PK2200

Table of Contents s v


Blank

vi s Table of Contents

PK2200


ABOUT THIS MANUAL
This manual provides instructions for installing, testing, configuring, and interconnecting the Z-World PK2200 controller. All product references in this manual are made to the PK2200 series. The term PK2200 is used as a generic term referring to any of the PK2200 series. Where necessary, specific model numbers are used. Instructions are also provided for using Dynamic C functions.
®

Assumptions
Assumptions are made regarding the user's knowledge and experience in the following areas. Ability to design and engineer the target system that a PK2200 will control. Understanding of the basics of operating a software program and editing files under Windows on a PC. Knowledge of the basics of C programming.

$


For a full treatment of C, refer to the following texts. The C Programming Language by Kernighan and Ritchie and/or C: A Reference Manual by Harbison and Steel

Knowledge of basic Z80 assembly language and architecture.

$

For documentation from Zilog, refer to the following texts. Z180 MPU User's Manual Z180 Serial Communication Controllers Z80 Microprocessor Family User's Manual

PK2200

About This Manual s vii


Acronyms
Table 1 lists and defines the acronyms that may be used in this manual.
Table 1. Acronyms
Acron ym Meaning

EPROM EEPROM LCD LED NMI PIO PRT RAM RTC SIB SRAM UART

Erasable Programmable Read-Only Memory Electronically Erasable Programmable Read-Only Memory Liquid Crystal Display Light-Emitting Diode Nonmaskable Interrupt Parallel Input/Output Circuit (Individually Programmable Input/Output) Programmable Reload Timer Random Access Memory Real-Time Clock Serial Interface Board Static Random Access Memory Universal Asynchronous Receiver Transmitter

Icons
Table 2 displays and defines icons that may be used in this manual.
Table 2. Icons
Icon Meaning Icon Meaning

$ (
FD

Refer to or see

!
7LS

Note

Please contact

Tip

Caution

High Voltage

Factory Default

viii s About This Manual

PK2200


Conventions
Table 3 lists and defines the typographic conventions that may be used in this manual.
Table 3. Typographic Conventions
Example Description

while // IN-01... Italics

Courier font (bold) indicates a program, a fragment of a program, or a Dynamic C keyword or phrase. Program comments are written in Courier font, plain face. Indicates that something should be typed instead of the italicized words (e.g., in place of filename, type a file's name). Sans serif font (bold) signifies a menu or menu selection. An ellipsis indicates that (1) irrelevant program text is omitted for brevity or that (2) preceding program text may be repeated indefinitely. Brackets in a C function's definition or program segment indicate that the enclosed directive is optional. Angle brackets occasionally enclose classes of terms. A vertical bar indicates that a choice should be made from among the items listed.

Edit ...

[] <> a|b|c

Pin Number 1
A black square indicates pin 1 of all headers.
Pin 1

Measurements
All diagram and graphic measurements are in inches followed by millimeters enclosed in parenthesis.

PK2200

About This Manual s ix

J1


Blank

x s About This Manual

PK2200


CHAPTER 1: OVERVIEW
Chapter 1 provides a comprehensive overview and description of the PK2200.

PK2200

Overview s 11


Introduction
The PK2200 is an inexpensive control computer well suited for a variety of applications in areas such as packaging, materials handling, and process control. Figure 1-1 illustrates the PK2200 with the 2 â 20 character LCD and a 2 â 6 keypad.
PLCBus Expansion Connector Screw Connectors LCD DISPLAY LED

menu
setup

item

field
run

up F4

down del

help
init

F1

F2

F3

add

Screw Connectors

Keypad

RS-232 Connector

Figure 1-1. PK2200 with Character LCD and Keypad

Figure 1-2 illustrates the PK2240 with the 128 â 64 graphic LCD and a 4 â 3 keypad.
PLCBus Expansion Connector Screw Connectors LCD DISPLAY LED

7 4 1 -

8 5 2 0

9 6 3 .

Screw Connectors

Keypad

RS232 Connector

Figure 1-2. PK2240 with Graphic LCD and Keypad 12 s Overview PK2200


Figure 1-3 illustrates the PK2200 without an enclosure.
DCIN U10, U16 are under the EPROM U8, U11 are under the SRAM

J1
JP1

LED
U3

L1

C1

U2

H.C. Driver
JP2 JP3

U5 U6 U7

485

U1

LCD
U4

PLC Bus Connector

U9

Buffer Y1 H1
U15

PLD RS232
U12

RS-232

EPROM

U13

Batter y

Buffer U14 Inv. H2 Mux

SRAM

RT U17
J2

RTC
Phone Jack
RJ-12

Z180
Y2

Beeper JP4
H3

U18 Keypad
U19

Mux

Mux

U20

RS-232 Connector
JP5 Reset Button

J3

Figure 1-3. PK2200 Without Enclosure

PK2200

Overview s 13


Standard Features
The PK2200 series includes the following standard features: Compact size: 4" â 5.5" â 1.34" 16 protected digital inputs for detecting contact closures, counting pulses, or detecting voltage input signals. 14 high-current digital outputs, suitable for driving relays, solenoids, or lamps. RS-485 and RS-232 serial ports for external communication and controller networking using links up to several kilometers 9.216 MHz clock with 18.432 MHz optional Switching power supply for reduced power consumption. The PK2200 consumes less than 2 W at 18.432 MHz. A PLCBus port allows system expansion including relays, A/D converters, D/A converters, UARTs and more. EPROM (up to 512K) or flash EPROM (up to 256K) for program and nonvolatile data storage. Battery-backed RAM (up to 512K). Battery-backed real-time clock with time and date functions. Programmable timers. EEPROM (512 byte standard) for storing system information. Watchdog timer and power-fail detection circuitry for improved system reliability. Table 1-1 lists PK2200 series models and each models standard features.
Table 1-1. PK2200 Series Standard Features
Model Features

PK2200 PK2210 PK2220 PK2230 PK2240

18.432 MHz clock, 2 â 20 character LCD, 2 â 6 keypad, rugged metal enclosure. 9.216 MHz clock, 2 â 20 character LCD, 2 â 6 keypad, rugged metal enclosure. 18.432 MHz clock, 2 â 20 character LCD, 2 â 6 keypad 9.216 MHz clock. 18.432 MHz clock, 128K flash EPROM, 128 â 64 backlit graphic LCD, 4 â 3 keypad, rugged metal enclosure.

14 s Overview

PK2200


Flexibility and Customization Options
The PK2200 is available with either quick-release pluggable terminals or fixed screw terminals. For added flexibility, special order the PK2200 Series controller with the following options installed. Backlit character LCD (for PK2200 and PK2210 only). 128K or 512K battery-backed RAM. 128K flash EPROM for program and nonvolatile data storage. High-voltage sourcing drivers. For quantity orders, customization of the PK2200 modified is available to better suit your application. A wide variety of options are available for I/ O, memory, and packaging.

(

For details on PK2200 customization, contact your Z-World Sales Representative at (530) 757-3737.

Development Kit
The PK2200 Development Kit contains all the tools required for fast development. The kit includes the following items: Programming cable Power supply 128K flash EPROM High-current sourcing drivers Demonstration board that simulates I/O User s manual with schematics

PK2200

Overview s 15


CE Compliance
The PK2200 has been tested by an approved competent body, and was found to be in conformity with applicable EN and equivalent standards. Note the following requirements for incorporating the PK2200 in your application to comply with CE requirements. The power supply provided with the Development Kit is for development purposes only. It is the customer s responsibility to provide a clean DC supply to the controller for all applications in end-products. Fast transients/burst tests were not performed on this controller. Signal and process control lines longer than 3 m should be routed in a separate shielded conduit. The PK2200, PK2210, PK2220, and PK2230 were tested to Industrial Immunity Standards. The PK2240 has been tested to Light Industrial Immunity standards. Additional shielding or filtering may be required for the PK2240 for an industrial environment. The PK2200 has been tested to EN55022 Class A emission standards. Additional shielding or filtering will be required to meet Class B emission standards.







$

Visit the Technical Reference pages of the Z-World Web site at http://www.zworld.com for more information on shielding and filtering.

16 s Overview

PK2200


CHAPTER 2: GETTING STARTED
Chapter 2 provides instructions for connecting the PK2200 to a PC and running a sample program.

PK2200

Getting Started s 17


Connecting the PK2200 to a PC
The PK2200 is programmed with a PC through an RS-232 port using the programming cable provided in the Development Kit. To connect the PK2200 to a PC use the following steps: 1. Install Dynamic C as described in your Dynamic C manuals. 2. Using the supplied adapter, connect the programming cable from the PK2200s RJ-12 (J2) socket to the appropriate COM port of your computer.
PK2200 Series Controller
To PC's COM Por t

Programming Cable

Adapter

Figure 2-1. Programming Connections

Only use the supplied adapter and programming cable.

!

The supplied 24 V wall power supply is sufficient for all power requirements. The PK2200 accepts from 9 V to 36 V DC.

3. Connect the supplied 24V DC power supply as follows. Connect the lead with the red sleeving to the +DC terminal of the PK2200 (J1 terminal 1). Connect the other lead to the GND terminal (J1 terminal 3).

18 s Getting Started

PK2200


Figure 2-2 illustrates the power supply connections.

GND

+DC

K

J1
+ Long Lead Red Shrink Wrap

Short Lead

Power Supply Leads

Figure 2-2. Power Supply Connection

4. Plug the power supply into a wall socket. The PK2200 is now ready to run.

Establishing Communication with the PK2200
To establish communication with the PK2200 use the following steps. 1. Double-click the Dynamic C icon to start the software. Note that each time you start Dynamic C, communication with the attached PK2200 is attempted. 2. If the communication attempt is successful, no error messages are displayed.

$ !

If an error message such as Target Not Responding or Communication Error is displayed, see Appendix A, Troubleshooting. After making necessary changes to establish communication between a PC and the PK2200, use the Dynamic C shortcut to reset the controller and initialize communication.

PK2200

Getting Started s 19


Running a Sample Program
To run a sample program on the PK2200 use the following steps. 1. Open the sample program CDEMO_RT.C located in the SAMPLES\CPLC Dynamic C subdirectory. 2. Compile the program by pressing F3 or by choosing Compile from the compile menu. Dynamic C compiles and downloads the program into the PK2200s memory. During compilation, Dynamic C rapidly displays several messages in the compiling window. This condition is normal.

$

If an error message such as Target Not Responding or Communication Error is displayed, see Appendix A, Troubleshooting.

3. Run the program by pressing F9 or by choosing Run from the Run menu. 4. To halt the program, press . 5. To restart program execution, press F9.

$

Refer to Z-Worlds Dynamic C Technical Reference User s Manual for instructions regarding the use of the Dynamic C development system.

20 s Getting Started

PK2200


CHAPTER 3: SUBSYSTEMS
Chapter 3 describes the various PK2200 subsystems and interfaces, software drivers and sample programs.

PK2200

Subsystems s 21


Subsystem Overview
The PK2200 is composed of several subsystems. The following list of subsystem elements is illustrated in Figure 3-1. Processor core Protected digital inputs High-voltage driver outputs Serial communication channels Keypad and LCD
Core

Z180

Real-Time Clock PIN01 PIN02 PIN03 PIN04 PIN05 PIN06 PIN07 PIN08 PIN09 PIN10 PIN11 PIN12 PIN13 PIN14 PIN15 PIN16 Battery RAM EEPROM EPROM

HV01 HV02 HV03 HV04 HV05 HV06 HV07 HV08 K HV09 HV10 HV11 HV12 HV13 HV14 High Voltage Digital Outputs

Protected Digital Inputs

OR
Flash EPROM

Beeper PLC Expansion 485+ 485­ RS-485 and RS-232 Serial Channels

RS485 LCD and Keypad

LCD & Keypad

RS232

Figure 3-1. PK2200 I/O Systems Block Diagram

22 s Subsystems

PK2200


Processor Core
The PK2200s processor core is composed of the CPU, microprocessor supervisor/watchdog timer, battery-backed static RAM, EPROM/flash EPROM, EEPROM, and RTC. CPU The PK2200 is available with either 9.216 MHz or 18.432 MHz CPU clock speeds. The 18.432 MHz clock improves system performance and allows baud rates up to 11,500 bps. PK2200s with the 9.216 MHz option are limited to 57,600 bps. The system clock speed is a 16-bit value stored at location 0x108 in the EEPROM. The clock speed is expressed in multiples of 1200 Hz. The value read for 9.216 MHz clocks is 7,680 and for 18.432 MHz clocks the value read is 15,360. Microprocessor Supervisor/Watchdog Timer The microprocessor supervisor/watchdog timer provides the following functions for the PK2200. Power monitoring for the processor. Protects the system during brownouts and fluctuating power conditions. The supervisor provides a power-fail output that can be monitored by the processor, allowing the processor to save important information before a complete power-fail and then halt operation until power is fully restored. Battery backup for the static RAM. Allows data to remain intact even when power is removed from the PK2200. Watchdog timer function. Resets the system in the event of a software or hardware error that causes the processor to enter an infinite loop. Static RAM Static RAM is normally used to store program data. RAM can also be used to store program code. This is especially useful during software development because it allows quick program changes without having to change EPROMs. EPROM/Flash EPROM EPROMs offer a low-cost, permanent medium for storing program code and constant data. Once the application program is fully functioning and debugged, an EPROM can be programmed and installed. EPROMs can be quickly and easily duplicated, and are easy to install.

PK2200

Subsystems s 23


Even though slightly more expensive than standard EPROM, flash EPROM offers the following benefits. · In-system programmability. · Remote downloading of program code and data. · Easier to reprogram. · Erases quicker without a special eraser. EEPROM EEPROM offers a separate area for storing permanent or semi-permanent information such as clock speed, network address, calibration coefficients, and installation data. The EEPROM can be write-protected using a jumper, which prevents data from being accidentally overwritten. Real Time Clock (RTC) The RTC provides the application program with the current date and time of day. The PK2200's battery keeps the RTC running even when the power is off. The RTC is accurate to about one second a day and compensates for leap years and variances in the number of days in each month.

Digital Inputs
The PK2200's 16 digital inputs (PN01 through PN16) are flexible and robust. Configurable pull-up or pull-down resistors and high voltage protection circuits allow the inputs to detect switch contacts, relay contacts, outputs from open-collector transistor devices, logic level outputs, and high voltage outputs. In addition, two inputs may be used for generating interrupts and another two may be used for high-speed counting. The protected digital inputs have the follwoing features: · Nominal input voltage range of ­20 V to +24 V. · Protection against overloads over the range of ­48 V to +48 V. · Logic level detection. · Configurable pull-ups and pull-downs. Jumper the digital inputs in groups of eight to pull up to +5 V or down to GND through 4.7 k resistors. The nominal voltage range for the protected digital inputs is -20 V to +24 V. The inputs are protected against overvoltages in the range -48 V to 48 V; however, inputs should not be regularly subjected to voltages outside the nominal voltage range. Logic-level signals can also be detected using the digital inputs. The logic threshold is nominally 2.5 V. The maximum guaranteed low voltage is 1.25 V. The minimum guaranteed high voltage is 3.75 V.
24 Subsystems PK2200


The digital inputs can be pulled up to +5 V or down to GND by installing jumpers on JP2. When jumpered, the digital input line impedance is 4.7 k in the range 05 V for inputs 110 and 1516. The impedance on inputs 1114 is approximately 1.5 k. Outside this range, the input impedance is greater than 3.9 k for inputs 110 and 1516. Jumper JP2 connects the inputs to pull-up or pull-down resistors. Table 3-1 lists the JP2 jumper settings and Figure 3-2 illustrates JP2 jumper settings.
Table 3-1. JP2 Digital Input Jumper Settings
Pins Jumpered Inputs Configuration

7­9 8­10 9­11 10­12

1­4 and 9­12 5­8 and 13­16 1­4 and 9­12 5­8 and 13­16

Pulled up Pulled up Pulled down Pulled down

Pull-up configuration JP2 1 3 5 7 9 11 2 4 6 8 10 12

Pull-down configuration JP2 1 3 5 7 9 11 2 4 6 8 10 12

Figure 3-2. JP2 Digital Input Jumper Settings

The Figure 3-3 illustrates a typical digital input line.
JP2
R = 2 k for inputs 11, 12, 13, and 14. R = 22 k otherwise

+5V

GND

4.7 k Inputs 116 R 0.01 µF

Select 1 8 or 9 16

D0D7

to Z180 if input 11, 12, 13, or 14

Figure 3-3. Typical Digital Input PK2200 Subsystems s 25


Inputs 1114, in addition to the protected digital input function, have the capabilities listed in Table 3-2.
Table 3-2. Digital Input 11-14 Alternate Functions
Input Z180 Signal Function

11 12 13 14

/INT0 /INT2 CKA0/DREQ0 /DREQ1

Interrupt for user programs Interrupt for user programs DMA channel 0, used for counting DMA channel 1, used for counting

Inputs 11 and 12 can be used to generate hardware interrupts on the PK2200 CPU. Input 11 is connected to /INT0 and input 12 is connected to /INT2. With Dynamic C, you can easily implement service routines for these interrupts. Table 3-2 lists the alternate functions for digital inputs 11 through 14.

$

Refer to the Dynamic C Technical Reference User s Manual for more information on writing interrupt service routines.

Inputs 13 and 14 are connected to the CPUs DMA channels. These inputs may be used for counting high-speed digital signals. For highspeed counting (above 5 kHz), remove capacitor network CN2.
EPROM
U19

Z180
CN1

RAM
U20 CN2 JP5

Mux

Mux

J3

Remove CN2 for high-speed counting

Figure 3-4. CN2 Capacitor Networks

!

Removing CN2 from the PK2240 disables the filtering on channels IN5, IN6, IN7, IN8, IN13, IN14, IN15, and IN16

The high-speed counters and can perform a variety of functions including time stamping, pulse width measurement and duty cycle measurement.
26 s Subsystems PK2200


Digital Outputs
The PK2200s 14 digital outputs (HV01 through HV14) provide highvoltage, high-current digital outputs for your application. Sinking and optional sourcing drivers will drive a variety of loads including inductive loads such as relays, small solenoids, or stepping motors. Note the following points regarding the digital outputs: Each output is individually addressable. Each output includes a protective diode that returns inductive spikes to the power supply. Sinking drivers are standard. Sourcing drivers are optional. Both drivers must be of the same type, either sinking or sourcing. The total number of outputs that can be on simultaneously is subject to chip power limits and ambient temperature. There are power limitations on each channel as well as the entire driver IC. Eight channels, HV1 HV8, are driven by one driver IC. The other six, HV9HV14, are driven by the other driver IC. Since fewer outputs are being driven by the HV9 HV14 driver IC, the current limit on these channels is higher than on the HV1HV8 channels. Figure 3-5 illustrates the configuration for the ULN2803 sinking driver.
inductive load external
HV01HV14 2 4 DC

JP1

K

Channel (114)

1 3

ULN2803

JP1

Figure 3-5. Sinking Driver Configuration

Note the following points regarding the ULN2803 sinking driver chip. Outputs pull low (sink current) when turned on. The chips rating is 48 V and 500 mA maximum per channel, subject to the chips thermal limits and ambient temperature. With all channels on, each channel can sink up to 170 mA continuously (100% duty cycle) as long as the chip temperature is less or equal to 50°C. At 70°C the current must be reduced to 140 mA or less.
PK2200 Subsystems s 27


Figure 3-6 illustrates the connection for the UDN2985A sourcing driver. (Note the connections on header JP1.)
12

K

JP1
Channel (114)

external DC

HV01HV14
43

inductive load

UDN2985A

JP1

Figure 3-6. Sourcing Driver Configuration

Note the following points regarding the UDN2985A sourcing driver. Outputs pull high (source current) when turned on. The chips rating is 30 V and 250 mA maximum per channel, subject to the chips thermal limits and ambient temperature. With all channels on, each channel can source up to 170 mA continuously (100% duty cycle) as long as the chip temperature is less or equal to 50°C. At 70°C the current must be reduced to 140 mA or less. Header JP1 configures the outputs for either sourcing or sinking drivers. Table 3-3 lists the JP1 jumper configurations shown in Figure 3-7.
Table 3-3. JP1 High-Current Output Jumper Settings
JP1 Setting Description
Sinking Drivers JP1
1 3 2 4

Sourcing Drivers JP1
1 3 2 4

1­3, 2­4 1­2, 3­4

Sinking Outputs Sourcing Outputs

Figure 3-7. JP1 Digital Output Jumper Settings

Tip

If incandescent lights are driven, use a series resistor to limit the incoming current. See Appendix B: Specifications for more detailed information on the sinking and sourcing drivers.

$

28 s Subsystems

PK2200


Serial Communication
Two serial ports support asynchronous communication at baud rates from 300 bps to 57,600 bps on 9.216 MHz versions up to 115,200 bps with the 18.432 MHz versions. The serial ports can be configured as follows: Two 3-wire RS-232 ports. One 5-wire RS-232 port (with RTS and CTS) and one half-duplex RS-485 port. The RJ-12 phone jack connector J2 supports full-duplex RS-232 communication with handshake lines. The RS-485 lines (J1 terminals 18 and 19) provide half-duplex asynchronous communication over twisted pair wires, up to 3 kilometers. The RS-232 ports on the PK2200 support a subset of the RS-232 standard that is in common use. Serial Channel Configuration Figure 3-8 illustrates the configuration of two 3-wire RS-232 channels.
TXD0 RXD0 TXD0 RXD0 13 11 RS-232CH1TX 7 5 RS-232CH1RX /TX0: J2-3

Z180

TXD1 RXD1

U12 (RS-232)

/RX0: J2-4 /TX1: J2-1 /RX1: J2-5

JP3
/RTS0 RX485 /CTS0 TXD1 R11 4.7k

U9 (RS-485)

485+: J1-18 485-: J1-19

Figure 3-8. Two RS-232 Channels

Figure 3-9 illustrates the configuration of one 5-wire RS-232 channel and one half-duplex RS-485 channel.
TXD0 RXD0 TXD0 RXD0 RS-232CH1TX RS-232CH1RX /TX0

Z180

TXD1 RXD1

U12 (RS-232)

/RX0 /TX1 = /RTS0 /RX1 = /CTS0

/RTS0 /CTS0

9 11 65

JP3
78 RXD1 = RX485 TXD1

U9 (RS-485)

485+ 485

Figure 3-9. RS-232 and RS-485 PK2200 Subsystems s 29


Table 3-4 lists JP3 jumper settings and Figure 3-10 illustrates jumper setting configurations for the two serial channels. If only one RS-232 channel is desired, use one of the first two configurations. With these configurations, the RS-485 port is also active on the second Z180 serial channel (Z1). Unless the application software explicitly enables Z1, the RS-485 channel has no effect on the Z180. The RS-485 is connected to Z1 in the first two configurations in order to keep the Z180 CMOS input (RXA1) from floating.
Table 3-4. JP3 Serial Communication Jumper Settings
JP3 Jumpered Pins Serial Communication Configuration

5­6, 7­8, 9­11 7­8 5­7 11­13

One 5-wire RS-232 channel (Z180 Port 0) with RTS/CTS One RS-485 channel (port 1) One 3-wire RS-232 One RS-485 Two 3-wire RS-232

FD

One 5-wire RS-232 and One RS-485 JP3 1 3 5 7 9 11 13 2 4 6 8 10 12 14

One 3-wire RS-232 One RS-485 JP3 1 3 5 7 9 11 13 2 4 6 8 10 12 14

Two 3-wire RS-232 JP3 1 3 5 7 9 11 13 2 4 6 8 10 12 14

Figure 3-10. JP3 Jumper Settings

30 s Subsystems

PK2200


Keypad and Display
The PK2200 Series supports operator I/O through both keypad and LCD. The following two standard operator I/O configurations are available on PK2200 controller models with enclosures: 2-row by 20-column character LCD module plus a 2-row by 6-column keypad. 128-column by 64-row backlit graphic LCD module plus a 4-row by 3-column keypad. The character LCD module is also available with an LED backlighting option and the graphic LCD has a software controllable electroluminescent backlighting installed as a standard feature. Table 3-5 lists and describes header connections and functions.
Table 3-5. Header Connections and Function
Header Function

H1 H2

The LCD connector. Connect a 14-wire ribbon cable from the LCD to this header. Not used on the PK2240. The PLCBus expansion connector. This connector supports the "LCD bus" as well. Use a 26-pin ribbon cable to attach PLCBus devices to the PK2200. The keypad connector. Connect a 10-wire flat flexible cable from the keypad to this header. Not used on the PK2240.

H3

The PK2200 series also interfaces easily with the Z-World line of operator interface products. Operator interfaces are available with a variety of keypad sizes and LCD configurations.

(

For more information on Z-World operator interfaces, contact your Z-World Sales Representative at (530) 757-3737.

PK2200

Subsystems s 31


Blank

32 s Subsystems

PK2200


CHAPTER 4: SYSTEM DEVELOPMENT
Chapter 4 describes system development using the PK2200 interfaces and presents some sample programs to illustrate their use.

PK2200

System Development s 33


Changing Modes
The operating mode of the PK2200 is determined during power-up initialization. If a valid program is found in EPROM, then it is executed. Otherwise, the operating mode is determined by the jumper settings on JP4 or by keypress combinations. Following are the possible modes of operation:. · Run a program stored in RAM or flash EPROM. · Prepare for Dynamic C programming using the RS-232 port. The mode can be changed by either of the following two methods: 1. Set jumper JP4 to the desired position. Remove power from the PK2200. Apply power to the PK2200. 2. With power off, hold down the appropriate keys on the keypad and apply power. Refer to Figure 4-1 for the appropriate keypress combinations. You will hear a series of beeps indicating that the mode has been set. The PK2240 has a sample program loaded at the factory that will run automatically when the PK2240 is powered. You can set the PK2240 to program mode using the procedures above. All other models are preconfigured for program mode.

Setting the Mode
Figures 4-1, 4-2, and 4-3 illustrate keypad and jumper settings for run and program modes for different PK2200 configurations. The keypress combination for the 3x4 keypad will work only with the PK2240 model. The keypress combination for the 2x6 keypad will work with any model with a 2x6 keypad. If programming at normal 19,200 bps, then press the "menu setup" and "up pgm" keys. If programming at 28,800 bps, then press the "menu setup" and the "down pgm" keys. You may instead set the programming baud rate with jumpers on JP4. At startup, a PK2200 can also be put into run mode by placing a jumper across pin 6 and pin 7 of JP4.

Program Mode
28,800 bps 19,200 bps
menu
setup

Run Mode
down
pgm

item
F2

field
run

up

help
init

menu
setup

item
F2

field
run

pgm

up

down
pgm

help
init

pgm

F1

F3

F4

del

add

F1

F3

F4

del

add

Figure 4-1. 2x6 Keypad Mode Settings 34 System Development PK2200


Program Mode
7 4 1 8 5 2 0 9 6 3

Run Mode
7 4 1 8 5 2 0 9 6 3

-

.

-

.

Figure 4-2. 3x4 Keypad Mode Settings

Program Mode
8 7 6 5 4 3 2 1

Run Mode
8 7 6 5 4 3 2 1

JP4
19,200 bps 28,800 bps

JP4

Figure 4-3. JP4 Mode Settings

Do not jumper more than one pair of pins to configure a mode.

Development Options
Memory Options
Programs for the PK2200 are written and compiled on a PC and then downloaded to the PK2200 memory and executed. There are three memory options for program storage on the PK2200: (1) Battery-backed RAM, (2) EPROM, (3) Flash EPROM.

Battery-Backed RAM
Battery-backed RAM is a standard feature on every PK2200. RAM is available in 32K, 128K, and 512K. During development you can use RAM to download and execute programs. This speeds development because you don't need to program and erase EPROMs. Once a program is fully debugged and running, you can create a binary file and use an EPROM burner to store the program in EPROM. Since the RAM is used to store both data and program, Z-World recommends using a larger RAM during development. If the PK2200 has flash EPROM installed, the program will be compiled to flash EPROM instead of RAM.

PK2200

System Development

35


EPROM
EPROMs offer a permanent storage option for programs and data. The PK2200 BIOS is factory installed in the EPROM. After an application is fully debugged and running, it can be compiled and stored in EPROM with an EPROM burner. Each time the PK2200 powers up, it will run the stored application.

Flash EPROM
Flash EPROM offers the benefits of both battery-backed RAM and standard EPROM. You can quickly change and download a program as if you were using RAM. Using flash EPROM frees up RAM for data storage rather than program storage. Flash EPROM does not depend upon the onboard battery to retain data, so a program is safe in the event that the battery is drained.

(

For more information on memory options or to place an order, contact your Z-World Sales Representative at (530) 757-3737.

Digital Inputs
The digital inputs can be used for a variety of applications such as detecting high-voltage and logic level digital signals, providing interrupts for time critical events, and high-speed counting.

Using the Digital Inputs
The digital inputs are supported in software by Dynamic C functions and virtual driver variables. There are several methods for reading the digital inputs. Some of the digital inputs have additional features listed below.

Interrupt Inputs
Inputs 11 and 12 can be used to generate level sensitive hardware interrupts on the PK2200 CPU. Interrupts can be used to signal events that need to be serviced in real-time.

High Speed DMA Counter
Two counters connected to digital inputs 13 and 14 are actually the CPUs DMA channel counters. The maximum counting speed is 1.5 MHz for 9.216 MHz PK2200 series controllers. The maximum counting speed is 3.0 MHz for 18.432 MHz PK2200 series controllers.

36 s System Development

PK2200


The following points summarize the counter s capabilities: The counter can measure the time at which a negative edge occurs with a precision of a few microseconds. A minimum time must occur between successive events to allow for interrupt processing. The counter can measure the width of a pulse by counting (up to 65,536) at a rate that varies from 300 Hz to 600 kHz, providing 16-bit accuracy. Count negative-going edges for up to two channels. The maximum count for high-speed counting (5 kHz and up) is 65,536. For low speeds, the maximum count is unlimited. Function calls load the count-down value for the DMA channel and enable the DMA interrupt. Once a counter reaches zero, flags for the DMA channel are set to 1. DMA flags can be monitored by an application program.

Digital Outputs
Using the Digital Outputs
The digital outputs are supported in software by Dynamic C functions and virtual driver variables. There are several methods for writing to the digital outputs. The digital outputs can be used for a wide variety of applications including the following: Driving solenoids, relays, motors and other inductive loads directly. Driving incandescent lamps, LEDs and resistive loads directly. Driving FETs, transistors, thyristors or solid state relays to increase the current or voltage output capability as well as providing a.c. drive capability.

PK2200

System Development s 37


Serial Communication
Dynamic C has serial communication support libraries. For the Z180 port z0 and Z180 port z1, use AASC.LIB, Z0232.LIB, and Z1232.LIB. For RS-232 expansion cards that interfaced through the PLCBus on the PK2200, use EZIOPLC.LIB. Functional support for serial communication includes the following: Initialization of the serial ports Monitoring, and reading, a circular receive buffer Monitoring, and writing to, a circular transmit buffer An echo option CTS (clear to send) and RTS (request to send) control for RS-232. XMODEM protocol for downloading and uploading data A modem option

!
FD

The PK2200 can be configured for either two channels or one RS-232 and one RS-485. Z0 only and Z1 may be configured for RS-232 or See Chapter 3 for information on configuring communication channels.

RS-232 is RS-232 RS-485. the serial

Z180 Port Z0 is configured at the factory for RS-232 and Port Z1 is configured for RS-485.

Receive and Transmit Buffers
Serial communication is made easier with a background interrupt routine that updates receive and transmit buffers. Every time a port receives another character, the interrupt routine places it into the receive buffer. A program can read the data one character at a time or as a stream of characters terminated by a special character. A program sends data by writing characters into the transmit buffer. If the serial port is not already transmitting, the write functions automatically initiate the transmission. Once the last character of the buffer is sent, the transmit interrupt is turned off. Data can be written one character at a time or as a stream of characters.

38 s System Development

PK2200


Echo Option
If the echo option is turned on during initialization of the serial port (with Dinit_z0, Dinit_z1, or Dinit_uart) any character received is automatically echoed back (transmitted out). This feature is ideal for use with a dumb terminal and also for checking the characters received.

CTS/RTS Control
Z180 port 0 is constrained by hardware to have the CTS (clear to send) pulled low by the RS-232 device with which it is communicating. An RS232 expansion card, however, can enable or disable the effect of the CTS line. Z180 port 1 does not support the CTS / RTS lines. If you choose the CTS/RTS option, the support software pulls the RTS (request to send) line high when the receive buffer has reached 80 percent of capacity. Thus, the transmitting device (if its CTS is enabled) stops transmitting. The RTS line is pulled low again when the received buffer has gone below 20 percent of capacity. If the device with which the PK2200 is communicating does not support CTS and RTS, the CTS and RTS lines on the PK2200s side can be tied together to make communication possible.

XMODEM File Transfer
The PK2200 supports the XMODEM protocol for downloading and uploading data. Currently, the library supports downloading an array of data whose size is a multiple of 128 bytes. Uploaded data is written to a specified area in RAM. The targeted area for writing should not conflict with the current resident program or data. During XMODEM transfers, character echo is automatically suspended.

Modem Communication
Modems and telephone lines allow serial communication across a great distance. If you choose the modem option, character streams that are read from the receive buffer are automatically scanned for modem commands. When a modem command is found, the software takes appropriate action. Normally, the communication package functions in COMMAND mode while waiting for valid modem commands or messages. Once a link is established, communication functions in DATA mode. However, the software continues to monitor the modem for a NO_CARRIER message. The software assumes that modem commands are terminated with CR, which is carriage return (0x0D). The modem option is easiest to use when the user protocol also has CR as the terminating character. Otherwise, the software has to check for two different terminating characters. The user s terminating character cannot be any of the ASCII characters used in modem commands, nor can it be a line-feed character.
PK2200 System Development s 39


Library functions for the RS-232 port support communication with a Hayes Smart Modem or compatible. Note the following points: The CTS, RTS, and DTR lines of the modem are not used. If the modem used is not truly Hayes Smart Modem compatible, the user has to tie the CTS, RTS, and DTR lines on the modem side together. The CTS and RTS lines on the PK2200 side also have to be tied together. A NULL connection is required for the TX and RX lines. A commercial NULL modem will have its CTS and RTS lines tied together on both sides. Figure 4-4 shows the correct modem to PK2200 wiring.
Modem Side RX TX GND RTS CTS DTR Controller Side RX TX GND RTS CTS

Figure 4-4. Null Modem Cable Connections

Following are descriptions for Z180 port 0 functions. Similar functions are available for the RS-232 (UART) expansion card. Please note the following substitutions: For the RS-232 expansion card, substitute uart for z0 in the function name. For Z180 port 1, substitute z1 for z0 in the function name. For example, the initialization routine for the Z180 port 0 is called Dinit_z0(). The equivalent function for the RS-232 expansion card is Dinit_uart() The equivalent function for Z180 port 1 is Dinit_z1().

$

Refer to Appendix F, PLCBus, for details on software support for the RS-232 expansion card.

40 s System Development

PK2200


Interrupt Handling for Z180 Port 0
Normally, a serial interrupt service routine would be declared with the compiler directive:
#INT_VEC SER0_VEC routine

However, if you use the same serial port for Dynamic C programming, your program has to be downloaded first with Dynamic C before the address of the serial interrupt service routine is loaded into the interrupt vector table. That is, the service routine must be loaded at run-time. The following function loads the address of the service function into the specified location in the interrupt vector table.
reload_vec (int vector, int(*serv_function)())

The #INT_VEC directive should not be used with this function. Once the service routine has taken over, you cant debug your program in Dynamic C. If you communicate with a serial device other than the PCs Dynamic C programming port, your program has to make sure that the hardware is properly configured before sending any messages. For example, when using Z180 port 0 for serial communication with a modem, use the PK2200s keypad to trigger serial port initialization. Without this trigger, the modem may not properly communicate with the support software because the initialization routine also sends initialization commands to the modem. When executable programs are generated either for EPROM or for downloading to RAM, there is no need for communication with Dynamic C. The compile-time directive #INT_VEC can then be used freely.

Remote Downloading
The PK2200 has the capability of remote downloading program code. This allows units to be reprogrammed in the field, eliminating the need to recall units for reprogramming or sending field service personnel to install new software. In order to use the remote download feature, the PK2200 must have a serial link to the remote PC, either a direct RS-232 link or a modem. The RS-232 connection is limited to several hundred feet. Modems allow communication over virtually unlimited distances. If you plan to use the remote download feature, make sure that the PK2200 has enough memory to store future program revisions and data. Refer to Dynamic C Technical Reference Manual for a detailed description of the remote downloading procedure.

PK2200

System Development s 41


Developing an RS-485 Network
The two-wire RS-485 serial-communication port and Dynamic-C network software allow network development. Screw terminal strip J1 provides a half-duplex RS-485 interface. The RS-485 signals are on screw terminals 18 and 19. The PK2200 and/or other controllers can be linked together over several kilometers. When configuring a multi-drop network, use single twisted pair wires on all controllers to connect RS-485+ to RS-485+ and RS-485- to RS-485. A diagram of a two-wire RS-485 network is shown in Figure 4-5. Any Z-World controller can be a master or a slave. A network can have up to 255 slave controllers, but only one controller can be the master. In a multidrop network, termination and bias resistors are required to minimize reflections (echoing) and to keep the network line active during an idle state. Only the first and last board on a multidrop RS-485 cable should have termination resistors. Therefore, when networking multiple boards via RS-485, remove termination resistors from all boards in the network, except for the first and last board of the network.

Figure 4-5. RS-485 Network

Only a single, solid conductor should be placed in a screw clamp terminal. Bare copper, particularly if exposed to the air for a long period before installation, can become oxidized. The oxide can cause a high resistance (~20 ohm) connection, especially if the clamping pressure is not sufficient. To avoid oxidation, use tinned wires or clean, shiny copper wire. If you are using multiple conductors or stranded wire, consider soldering the wire bundle or using a crimp connector to avoid a later loss of contact pressure to a spontaneous rearrangement of the wire bundle. Soldering may make the wire subject to fatigue failure at the junction with the solder if there is flexing or vibration.
42 s System Development PK2200

GND 485­ GND 485­

PIN16 485+ PIN16 485+

PIN15 HV14 PIN15 HV14

PIN14 HV13 PIN14 HV13

PIN13 HV12 PIN13 HV12

PIN12 HV11 PIN12 HV11

PIN11 HV10 PIN11 HV10

PIN10 HV09 PIN10 HV09

PIN09 HV08 PIN09 HV08

+5V HV07 +5V HV07

PIN08 HV06 PIN08 HV06

PIN07 HV05 PIN07 HV05

PIN06 HV04 PIN06 HV04

PIN05 HV03 PIN05 HV03

PIN04 HV02 PIN04 HV02

PIN03 HV01 PIN03 HV01

PIN02 GND PIN02 GND

PIN01 RUN K PIN01 RUN K

GND PROGRAM +DC GND PROGRAM +DC


Keypad and LCD
The PK2200 Series supports operator I/O with a keypad and LCD. Two standard operator I/O configurations are available on PK2200 series controllers with enclosures: 2-row by 20-column character LCD module with a 2-row by 6column keypad. 128-column by 64-row backlit graphic LCD module with a 4-row by 3-column keypad. The character LCD module is also available with an LED backlighting option. The graphic LCD has electroluminescent backlighting installed as a standard feature.

Using the Keypad and Display
The PK2200 keypad and display are supported by a large number of software drivers. The keypad and display can be used for a variety of user interface applications including the following: User code or password entry System status display Multiple language/character-set displays Parameter monitoring and adjustment

PK2200 Keypads
Table 4-1 shows standard keypad configurations.
Table 4-1. Keypad Configurations
Model Keypad

PK2200 PK2210 PK2220 PK2230 PK2240

2x6 2x6 None None 4x3

PK2200

System Development s 43


Keypad Insert The keypads are duced on regular customization of

Templates designed to accept paper inserts. Inserts can be propaper using a laser printer, thus allowing quick and easy keypad legends.

You can use the templates below for creating inserts. All dimensions are in inches. Inserts can be secured by taping the portion of the insert that extends beyond the keypad to the supporting bracket
0.10

1.13

0.13

menu

item

field

up F4

down

help

0.10

0.40

F1

F2

F3

del

add

0.30

0.40 0.13 0.40

3.75

Figure 4-6. 2x6 Keypad Insert Template

0.40

7 4
0.25 0.25 0.15 2.10

8 5 2 0

9 6 3 .
0.05

1 ­
0.25 0.15

0.05

1.15

Figure 4-7. 3x4 Keypad Insert Template

44 s System Development

PK2200


Keypad Codes The PK2200 keypads are supported by Dynamic C functions that return codes corresponding to the key pressed. The figures below show the codes for the 2x6 and 3x4 keypads used on the PK2200 Series controllers.

1 7

2 8

3

45

6

9 10 11 12
Figure 4-8. 2x6 Keypad Codes

24 25 26 16 17 18 8 0 9 1 10 2

Figure 4-9. 3x4 Keypad Codes

PK2200

System Development s 45


PK2200 LCDs
The PK2200 Series LCDs are easy to use with Dynamic C software libraries. Shown below are the layouts for both the 2x20 character display and the 64x128 graphic display.
2x20 Character LCD
Row 0 Row 1

Column 0

Column 19

Figure 4-10. 2X20 Character LCD

64x128 Graphic LCD
Row 0

Row 63 Column 0 Column 127

Figure 4-11. 64X128 Graphic LCD

Graphic LCD Status Several Dynamic C library functions return the operating status of the LCD. The LCD status bits are shown in the following bitmap.
7 6 5 4 3 2 1 0

BUSY

0

ON/OFF

RESET

0

0

0

0

Most significant bit

Lea st significa nt bit

BUSY - Reading a 1 indicates LCD is performing an operation. Reading a 0 indicates the LCD is ready to accept more data.

46 s System Development

PK2200


ON/OFF - When the ON/OFF bit is set ( 1 ) the display is on, any image on the screen will be visible. When the bit is reset ( 0 ) any images on the display will not be visible. The image is still in the display memory. RESET - Resets the LCD module when low ( 0 ). Bitmapped Graphics Many of the Dynamic C functions that operate on the graphic LCD use bitmaps. These bitmaps represent the images on a section of the display. An individual dot, or pixel, is represented by one bit in the bitmap. If the pixel is on, the corresponding bit is set. If the pixel is off, the corresponding pixel is reset. The image on the display is two-dimensional (width and height). The bitmap used to store that display information is a one-dimensional array. Two-dimensional images are stored in column major, byte aligned bitmap format. Column major means that bits are stored in the bitmap column by column. The first pixel of the first column (row 0, column 0) of the image is stored in the first bit position in the bitmap. The second pixel of the first column is stored in the second bit position in the bitmap and so on. When the entire first column is stored in the bitmap, the process begins again with the second column and repeats until all columns of the image are stored. Byte aligned means that a column data will end on a byte boundary. If a column has a number of bits that is not evenly divisible by eight, then the remaining bits of the last byte representing a column will be left unused. Image data from the next column will be stored starting in the next byte.

PK2200

System Development s 47


Blank

48 s System Development

PK2200


CHAPTER 5: SOFTWARE REFERENCE
Chapter 5 covers the software drivers used with the PK2200 series controllers.

PK2200

Software Reference s 49


Software Drivers
Drivers are functions that simplify accessing PK2200 hardware and I/O. For the following reasons, Z-World drivers make writing software easier: Provide commonly needed functionality. Eliminate the need to know all of the details of operation. Previously tested. Simplify source code by replacing multiple lines of code with one function call.

$

Refer to the Dynamic C Technical Reference Manual for more information on using drivers.

Real Time Clock (RTC)
The RTC keeps the date and the time of day with a resolution of one second. The worst case error is 50ppm (4.3 seconds) per day. Leap years and variances in the number of days in a month are automatically tracked. The following structure holds the time and date:
struct char char char char char char char }; tm tm tm tm tm tm tm tm { _sec; _min; _hour; _mday; _mon; _year; _wday; // // // // // // // 0-59 0-59 0-23 1-31 1-12 0-150 (1900-2050) 0-6 where 0 means Sunday

The following routines read and write to the real-time clock: int tm_wr( struct tm *x ) Sets the system time to the values in the structure pointed to by *x. PARAMETER1: Pointer to the structure holding the system time information to be written. RETURN VALUE: 0 if successful; -1 if clock failing or not installed. int tm _ rd( struct tm *t ) Reads the current system time into the structure t. PARAMETER1: Pointer to the structure used to store the system time. RETURN VALUE: 0 if successful; -1 if clock failing or not installed.

50 s Software Reference

PK2200


EEPROM
The following functions provide access to the EEPROM. The EEPROM is generally used for storing system information, calibration information, or any data that does not need to change often. int ee _ rd (int address) Reads value from EEPROM at specified address. PARAMETER1: The address to read from. RETURN VALUE: EEPROM data (0-255) if successful; negative value if unable to read EEPROM. int ee_wr (int address, char data) Writes value to EEPROM at specified address. PARAMETER1: The address to write to. RETURN VALUE: Returns 0 if write is successful, negative value if unsuccessful.

PK2200

Software Reference s 51


Digital Inputs and Outputs
DIGIN1, DIGIN2, ..., DIGING16 The virtual driver variables DIGIN1, DIGIN2, ... DIGIN16 represent the state of the digital inputs. These variables take the value 1 if the input is high and 0 if the input is low. The value is changed only if the new value remains the same for 2 ticks (25 to 50 milliseconds) of the virtual driver. void VIOInit();
VIOInit is a dummy function used as a host for the GLOBAL_INIT of

the virtual I/O variables. Virtual inputs are read and virtual outputs are written out whenever the function VIODrvr() is called. Inputs are DIGIN1 to DIGIN16. Outputs are OUT1 to OUT16. The DIGIN values have to be the same for two successive reads to be valid. RETURN VALUE: None.

void VIODrvr(); Updates the virtual inputs DIGIN1 to DIGIN16. The virtual outputs OUT1 to OUT14 are send out to corresponding output ports. RETURN VALUE: None.

Digital Input Drivers
There are several methods for reading digital inputs and setting digital outputs on the PK2200. Below is a listing of drivers for the digital inputs and outputs, including the high-speed DMA counters. int up_digin( int channel ) Read the value at the specified digital input channel (116). RETURN VALUE: The function returns 1 when the channel is high and 0 when the channel is low. unsigned inport( unsigned port ) Reads value from I/O port. PARAMETER: port is the I/O port to be read. RETURN VALUE: Value from I/O port. You can read multiple PK2200 digital inputs simultaneously using the inport() function.
DIGBANK1 is the address ( 0x180 ) of the first eight digital inputs DIN1

through DIN8. Bit zero represents the state of DIN1, bit one is DIN2, etc. DIGBANK2 is the address ( 0x181 ) of the second eight digital inputs DIN9 through DIN16. Bit zero represents the state of DIN9, bit one is DIN10, etc.
52 s Software Reference

PK2200


The lower eight bits returned by the inport() function represent the status of the digital inputs. Bits which are set ( 1 ) represent inputs which are high. Bits which are reset ( 0 ) correspond to inputs which are low. Example:
lowDIBank = inport( DIGBANK1 ); highDIBank = inport( DIGBANK2 );

void DMA0Count (unsigned int count) Loads the DMA channel 0 with the count value and enables the DMA channel 0 interrupt. The function sets the flag _DMAFLAG0 to zero. When count negative edges have been detected, the channel causes an interrupt, and the interrupt service routine sets the flag _DMAFLAG0 to 1. A program can monitor _DMAFLAG0 to determine if the number of counts has occurred. PARAMETER: count is the number of pulses to count. RETURN VALUE: None void DMA1Count (unsigned int count) Loads DMA channel 1 with the count value and enables the DMA channel 1 interrupt. The function sets the flag _DMAFLAG1 to zero. When count negative edges have been detected, the channel causes an interrupt, and the interrupt service routine sets the flag _DMAFLAG1 to 1. A program can monitor _DMAFLAG1 to determine if the number of counts has occurred. PARAMETER: count is the number of pulses to count RETURN VALUE: None unsigned int DMASnapShot (byte channel, unsigned int *count) Reads the number of pulses that a DMA channel has counted. A DMA counter is initialized with one of the two preceding functions. PARAMETERS: channel is the DMA channel (0 or 1)
*count is a pointer to variable holding the pulse count.

RETURN VALUE: 0, if pulse train is too fast to have a snap shot taken; 1, if a snap shot is obtained and valid data is in *count.

!
PK2200

Even if a program is unable to read the counts, DMA interrupts still occur when the DMA channel counts down from its loaded value.
Software Reference s 53


Digital Output Drivers
Following are the digital output drivers for the PK2200: int up_setout( int channel, int value ) Sets the state of digital output. PARAMETER1: The digital output channel to set. PARAMETER2: The state to set. 1 (active) or 0 (inactive). RETURN VALUE: None. Pass channel (114) and value: 0 for OFF, 1 for ON. OUT1, OUT2, ..., OUT14 Set the virtual driver variables OUT1, OUT2, OUT3, ... OUT13, OUT14 to a value of 0 to turn off the output, or 1 to turn on the output. void outport(unsigned port, unsigned value); Writes value to I/O port. PARAMETER1: The output port. PARAMETER2: The value to be written. RETURN VALUE: None The addresses DRV1 - DRV14 are the port addresses for the digital ouputs. Writing 0 to any of these ports will turn the ouput OFF. To turn ON digital ouputs 1 through 8 write 0x20 to the corresponding port. For digital outputs 9 through 14 write 0x40 to turn the ouput ON.

!

The digital outputs are individually addressed and must be set one at a time.

54 s Software Reference

PK2200


LCD and Keypad
The following functions provide routines for writing to the LCD and reading the keypad. Include the following directives in your program if using the PK2240.
#use wintek.lib #use kp.lib

The following directives provide information to the compiler about the graphic LCD and keypad on the PK2240. void lc_init_keypad() Initializes timer1, keypad driver, and variables, and, if used, the realtime kernel. RETURN VALUE: None. int lc_kxget (byte mode) Fetches the key value from the FIFO keypad buffers. If mode = 0, value is removed from the buffer; otherwise, value remains in the buffer. RETURN VALUE: Key value or -1, if no key is available.

$

The Keypad and LCD section in Chapter 4 describes key values.

void lc_kxinit() Initialize the keypad driver and accessory variables. If virtual watchdogs are defined the virtual watchdogs are initialized. RETURN VALUE: None. void lc_setbeep (int count) Sounds the beeper for the number of 1280 Hz cycles specified by count. RETURN VALUE: None. up_beep (int milliseconds) Sets beeper on for specified number of milliseconds. Scaling of the count passed is dependent on the periodic routines that calls lc_beepscan. If BeepScale is undefined, it is defaulted to 0.04. RETURN VALUE: None. void lc_char (char ch) Sends a character to the LCD. The function waits for the LCD to become free before sending the character. RETURN VALUE: None
PK2200 Software Reference s 55


int lc_cmd (int cmd) Waits for LCD busy flag to clear, then sends cmd to LCD command register. RETURN VALUE: 0, if successful in writing to the LCD; else -1, if timeout void lc_ctrl (byte cmd) Write a control cmd to the LCD. RETURN VALUE: None. void lc_init() Initializes the LCD. The display is turned on, cleared, and the cursor (now in the top left character position) blinks. RETURN VALUE: None void lc_ n l() Performs a new line function on the LCD. RETURN VALUE: None void lc_ pos (int line, int column) Positions the cursor at the line designated by line and column designated by column on the LCD. RETURN VALUE: None void lc_printf (char* fmt, ...) Performs a printf to the LCD. The function arguments are specified as they are for the standard printf. RETURN VALUE: None int lc_wait() Waits for LCD busy flag to clear. Caution, doesnt time out. RETURN VALUE: 0, when LCD busy flag has cleared; else -1, if timeout after ten tries. void glSetBrushType(int type) Sets the brush type for all following graphics operations in this library. It controls how pixels are drawn on the screen with respect to existing pixels.
GL_SET for forcing pixels on, GL_CLEAR for forcing pixels off, GL_XOR for toggling the existing pixels and GL_BLOCK to overwrite the

PARAMETER1: This is the type of the brush. Possible values are entire memory location corresponding to the pixel. RETURN VALUE: None.

56 s Software Reference

PK2200


int glInit() Initializes the LCD module (software and hardware). RETURN VALUE: returns the status of the LCD. If the initialization was successful, this function returns 0. Otherwise, the returned value indicates the LCD status. int glBlankScreen() Blanks the screen of the LCD. RETURN VALUE: The returned value indicates the status of the LCD after the operation. int glPlotDot(int x, int y) Plots one pixel on the screen at coordinate (x,y). PARAMETER1: the x coordinate of the pixel to be drawn. PARAMETER2: the y coordinate of the pixel to be drawn. RETURN VALUE: Status of the LCD after the operation. void glPlotLine(int x1, int y1, int x2, int y2) Plots a line on the LCD. PARAMETER1: x coordinate of first endpoint. PARAMETER2: y coordinate of first endpoint. PARAMETER3: x coordinate of second endpoint. PARAMETER4: y coordinate of second endpoint. RETURN VALUE: None. void glPutBitmap(int x, int y, int bmWidth, int bmHeight, char *bm) Displays a bitmap stored in root memory on the LCD. For bitmaps defined in xmem memory, use glXPutBitmap. PARAMETER1: x coordinate of the bitmap (left edge). PARAMETER2: y coordinate of the bitmap (top edge). PARAMETER3: width of the bitmap. PARAMETER4: height of the bitmap. PARAMETER5: pointer to the bitmap. RETURN VALUE: None.

PK2200

Software Reference s 57


void glXPutBitmap(int x, int y, int bmWidth, int bmHeight, unsigned long bmPtr) Displays a bitmap stored in xmem on the LCD. For bitmaps stored in root memory, use glPutBitmap. PARAMETER1: x coordinate of the bitmap (left edge). PARAMETER2: y coordinate of the bitmap (top edge). PARAMETER3: width of the bitmap. PARAMETER4: height of the bitmap. PARAMETER5: pointer to the bitmap. RETURN VALUE: None. void glGetBitmap(int x, int y, int bmWidth, int bmHeight, char *bm) Gets a bitmap from the LCD. PARAMETER1: x coordinate of the bitmap (left edge). PARAMETER2: y coordinate of the bitmap (top edge). PARAMETER3: width of the bitmap. PARAMETER4: height of the bitmap. PARAMETER5: pointer to the bitmap. RETURN VALUE: None. void glFontInit(struct _fontInfo *pInfo, char pixWidth, char pixHeight, unsigned startChar, unsigned endChar, char bitmapBuffer) Initializes a font descriptor with the bitmap defined in the root memory. For fonts with bitmaps defined in xmem, use glXFontInit. PARAMETER1: pointer to the font descriptor to be initialized. PARAMETER2: width of each font item (must be uniform for all items). PARAMETER3: height of each font item (must be uniform for all items). PARAMETER4: offset to the first useable item (useful for fonts for ASCII or other fonts with an offset). PARAMETER5: index of the last useable font item. PARAMETER6: pointer to a linear array of font bitmap. RETURN VALUE: None.

58 s Software Reference

PK2200


void glXFontInit(struct _fontInfo *pInfo, char pixWidth, char pixHeight, unsigned startChar, unsigned endChar, unsigned long xmemBuffer) Initializes a font descriptor that has the bitmap defined in xmem. For bitmaps defined in root memory, use glFontInit. PARAMETER1: pointer to the font descriptor to be initialized. PARAMETER2: width of each font item (must be uniform for all items). PARAMETER3: height of each font item (must be uniform for all items). PARAMETER4: offset to the first useable item (useful for fonts for ASCII or other fonts with an offset). PARAMETER5: index of the last useable font item. PARAMETER6: pointer to a linear array of font bitmap. RETURN VALUE: None. void glPutFont(int x, int y, struct fontInfo *pInfo, unsigned code) Puts an entry from the font table to the LCD. PARAMETER1: x-coordinate of the entry (left edge). PARAMETER2: y-coordinate of the entry (top edge). PARAMETER3: pointer to the font descriptor that describes the font table to be indexed. PARAMETER4: code (offset) in the font table that indexes the bitmap to display. RETURN VALUE: None. void glVPrintf(int x, int y, struct fontInfo *pInfo, char *fmt, void *firstArg) Prints a formatted string on the LCD screen, similar to vprintf. PARAMETER1: x coordinate of the text (left edge). PARAMETER2: y coordinate of the text (top edge). PARAMETER3: pointer to font descriptor that describes the font used for printing the text. PARAMETER4: pointer to the string that describes the format. PARAMETER5: pointer to the first argument to instigate the format string.
PK2200

RETURN VALUE: None.

Software Reference s 59


void glPrintf(int x, int y, struct _fontInfo *pInfo, char *fmt,...) Prints a formatted string (much like printf) on the LCD screen. PARAMETER1: x coordinate of the text (left edge). PARAMETER2: y coordinate of the text (top edge). PARAMETER3: pointer to the font descriptor used for printing on the LCD screen. PARAMETER4: pointer to the format string RETURN VALUE: None. void glPlotCircle(int xc, int yc, int rad) Draws a circle on the LCD. PARAMETER1: x coordinate of the center. PARAMETER2: y coordinate of the center. PARAMETER3: radius of the circle. RETURN VALUE: None. int wtDisplaySw(int onOff) Switches the display on and off. PARAMETER1: If this parameter is 1, the display is turned on. If this parameter is 0, the display is turned off. RETURN VALUE: Status of the LCD after the operation. void kdiELSw(int value) Switchs the EL backlight of the LCD. PARAMETER1: 1 to turn the backlight on, 0 to turn the backlight off. RETURN VALUE: None. void kdiSetContrast(unsigned content) Sets the contrast control to content. PARAMETER1: Specifies the contrast (the higher the value, the higher the contrast). RETURN VALUE: None

60 s Software Reference

PK2200


void kpInit(int (*changeFn)()) Initializes the kp module. This function should be called before other functions of this module are called. PARAMETER1: This is a pointer to a function that will be called when the driver detects a change (when kpScanState is called). Two arguments are passed to the call-back function. The first argument is a pointer to an array that indicates the current state of the keypad. The second pointer is a pointer to an array that indicates what keypad positions are changed and detected by kpScanState. The byte offset in the array represents the line pulled high (row number), and the bits in a byte represents the positions (column number) read back. RETURN VALUE: None int kpScanState() Scans the keypad and detect any changes to the keypad status. Returns non-zero if there is any change. If kpInit is called with a non-NULL function pointer, that function will be called with the state of the keypad. This function should be called periodically to scan for keypad activities. RETURN VALUE: 0 if there is no change to the keypad, non-zero if there is any change to the keypad. int kpDefStChgFn(char *curState, char *changed)
kpDefGetKey. This function is called back by kpScanState when kpDefGetKey, the new key pressed will not be registered.

This is the default state change function for the default get key function

there is a change in the keypad state. If the current key is not read by

PARAMETER1: Points to an array that reflects the current state of the keypad (bitmapped, 1 indicates key is not currently pressed). PARAMETER2: Points to an array that reflects the CHANGE of keypad state from the previous scan. (bitmapped, 1 indicates there was a change). RETURN VALUE: -1 if no key is pressed. Otherwise it returns the normalized key number. The normalized key number is 8*row+col+edge*256. Edge is 1 if the key is released, and 0 if the key is pressed.

PK2200

Software Reference s 61


int kpDefGetKey() This is the default get key function. This function returns the key previously pressed (i.e., from the one-keypress buffer). The key pressed is actually interpreted by kpDefStChgFn, which is called back by kpScanState. The function kpDefInit should be used to initialize the module. RETURN VALUE: -1 if no key is pressed. Otherwise it returns the normalized key number. The normalized key number is 8*row+col+edge*256. Edge is 1if the key is released, and 0 if the key is pressed. void kpDefInit() Initializes the module to use the default state change function to interpret key presses when kpScanState is called. Use kpDefGetKey to get the code of the last key pressed. RETURN VALUE: NA.

Sample Programs
The sample programs listed in Table 5-1 are specific to the PK2200. They can be found in the SAMPLES\CPLC directory.
Table 5-1. PK2200 Sample Programs
Program Description

5KEYCODE.C 5KEYDEMO.C 5KEYLAD.C 5KEYLINK.C 5KEYSCAN.C CDEMO_RT.C DIGDEMO.C DIGVDVR.C DMACOUNT.C

Code-driven sample program for the five-key system. Uses a code-driven five-key system and the RT-kbyte for I/O monitor and control. Combines 5KEYCODE.C and LADDERC.C. Linked-list sample program for the five-key system. Combines 5KEYCODE.C and SCANBLK.C. Demonstrate the use of the real-time kernel. Use the keypad to select which digital input channel to monitor. Similar to DIGDEMO.C. but uses the virtual driver to monitor the state of the input. Demonstrates the use of the high speed counters.

continued...
62 s Software Reference PK2200


Table 5-1. PK2200 Sample Programs (concluded)
Program Description

LADDERC.C LCGRAM.C OUTDEMO.C OUTVDVR.C PRT0DEMO.C READIO.C READKEY.C SCANBLK.C UREADIO.C VWDOG.C

Use ladder C for I/O control. Illustrates use of the LCD character generator. Use keypad to toggle the state of the digital outputs. Similar to OUTDEMO.C, but uses the virtual driver to change the state of the output. Use TIMER0 for timer interrupt . Read and toggle the I/Os through STDIN. The I/Os are driven by function calls. Read the keypad and write to the LCD and to the STDIO window. Use function blocks for I/O control. Read and toggle the I/Os through STDIN. The I/Os are driven by the virtual driver. Illustrates the use of the virtual watchdogs and of KEYREQUEST

Communication Sample Programs
The sample communication programs listed in Table 5-2 are located in the SAMPLES\NETWORK directory.
Table 5-2. Sample Communication Programs
Program Description

CSREMOTE.C

Slave version of CZ0REM.C, that includes most capabilities of CZ0REM.C. Master-to-slave communication is via opto22 9th-bit binary protocol. Same as CZ0REM.C but uses XP8700 expansion card.

CUARTREM.C

continued...

PK2200

Software Reference s 63


Table 5-2. Sample Communication Programs (concluded)
Program Description

CZ0REM.C

More elaborate sample of serial communication between board and PC dumb terminal. Includes modem communication, data monitoring, time and date setup, memory read and write, data logging, XMODEM download of the data log, XMODEM upload of binary file for remote downloading. Also supports master-to-slave communication. (Slave has to be running the program CSREMOTE.C.) RS-232 communication with a PC dumb terminal, with or without modem. Also, master-to-slave communication with another board running RS-485.C. Slave program to communicate with the master running RS-232.C. RS-232 communication through an RS-232 expansion card with the PK2200. An RS-232 program for Z180 port 1.

RS232.C

RS485.C UART232.C Z1232.C

PK2240 Sample Programs
The sample programs listed in Table 5-3 are specific to the PK2240 and are located in the SAMPLES\PK224X directory. These programs illustrate the use of the graphic LCD and keypad.
Table 5-3. PK2240 Sample Programs
Program Description

GLPRINTF.C KPDEFLT.C

Demonstrates the glprintf function and shows how to print text on the graphics display. Demonstrates key scanning techniques using functions in the KP library.

64 s Software Reference

PK2200


APPENDIX A: TROUBLESHOOTING
Appendix A provides procedures for troubleshooting system hardware and software.

PK2200

Troubleshooting s 65


Out of the Box
Check the items mentioned in this section before starting development. Verify that the PK2200 runs in standalone mode before connecting any expansion boards or I/O devices. Verify that the entire host system has good, low-impedance, separate grounds for analog and digital signals. Often the controller is connected between the host PC and another device. Any differences in ground potential from unit to unit can cause serious problems that are hard to diagnose. Do not connect analog ground to digital ground anywhere. Double-check the connecting ribbon cables to ensure that all wires go to the correct headers. Verify that the host PCs COM port works by connecting a good serial device to the COM port. Remember that COM1/COM3 and COM2/ COM4 share interrupts on a PC. User shells and mouse drivers, in particular, often interfere with proper COM port operation. For example, a mouse running on COM1 can preclude running Dynamic C on COM3. Use the supplied Z-World power supply. If another power supply must be used, verify that it has enough capacity and filtering to support the PK2200. Use the supplied Z-World cables. The most common fault of usermade cables is failure to properly assert CTS at the RS-232 port of the controller Without CTSs being asserted, the controllers RS-232 port will not transmit. Assert CTS by either connecting the RTS signal of the PCs COM port or looping back the PK2200s RTS. Experiment with each peripheral device connected to the controller to determine how it appears to the controller when powered up, powered down, and/or when its connecting wiring is open or shorted. If a DB9 connector or an RJ-12 connector is wired up to a 10-pin connector, carefully check the connections. These wires do not run pin-for-pin. Note: Telephone company wiring does not follow a standardized color code.











66 s Troubleshooting

PK2200


Dynamic C Will Not Start
In most situations, when Dynamic C will not start, an error message announcing a communication failure will be displayed. Following is a list of situations causing an error message and possible resolutions. Wrong Baud Rate In rare cases, the baud rate has to be changed when using the Serial Interface Board for development. Wrong Communication Mode Both sides must be talking RS-232. Wrong COM Port A PC generally has two serial ports, COM1 and COM2. Specify the one being used in the Dynamic C Target Setup menu. Use trial and error, if necessary. Wrong Operating Mode Communication with Dynamic C will be lost if the controller s jumper is set for standalone operation. Reconfigure the board for programming mode. Wrong Memory Size Jumpered pins on JP2 specify the EPROM size.





If all else fails, connect the serial cable to the controller after power up. If the PCs RS-232 port supplies a large current (most commonly on portable and industrial PCs), some RS-232 level converter ICs go into a nondestructive latch-up. Connect the RS-232 cable after power up to eliminate this problem.

Dynamic C Loses Serial Link
If the program disables interrupts for a period greater than 50 milliseconds, Dynamic C will lose its serial link with the application program. Make sure that interrupts are not disabled for a period greater than 50 milliseconds.

PK2200 Repeatedly Resets
The PK2200 resets every 1.0 seconds if the watchdog timer is not hit. If a program does not hit the watchdog timer, then the program will have trouble running in standalone mode. To hit the watchdog, make a call to the Dynamic C library function hitwd.

PK2200

Troubleshooting s 67


Common Programming Errors
Values for constants or variables out of range. Table A-1 lists acceptable ranges for variables and constants.
Table A-1. Constant and Variable Ranges
Type Range

int long int float char

­32,768 (­2 ) to 15 +32,767 (2 ­1) -2 , 147,483,648 ( - ) to 2 31 1 +2147483647 (2 - )
31

15

1.18 â 10 to 38 3.40 â 10 0 to 255

­38



Mismatched types. For example, the literal constant 3293 is of type int (16-bit integer). However, the literal constant 3293.0 is of type float. Although Dynamic C can handle some type mismatches, avoiding type mismatches is the best practice. Counting up from, or down to, one instead of zero. In software, ordinal series often begin or terminate with zero, not one. Confusing a functions definition with an instance of its use in a listing. Not ending statements with semicolons. Not inserting commas as required in functions parameter lists. Leaving out ASCII space character between characters forming a different legal, but unwanted operator. Confusing similar-looking operators such as && with &, == with =, and // with /. Inadvertently inserting ASCII nonprinting characters into a source-code file.



68 s Troubleshooting

PK2200


APPENDIX B: SPECIFICATIONS
Appendix B provides comprehensive PK2200 physical, electronic, and environmental specifications.

PK2200

Specifications s 69


General Specifications
Table B-1 lists the electrical, mechanical, and environmental specifications for the PK2200.
Table B-1. PK2200 General Specifications
Parameter Specification

Operating Temp Humidity Input Voltage Digital Inputs Digital Outputs Processor Clock SRAM EEPROM Flash EPROM Serial ports Serial rate Watchdog/supervisor Time/date clock Backup battery

-40° C to 70° C 5% to 95%, noncondensing 9 V to 24 V DC 16 protected, - 0 V to +24 V DC 2 14 high-current sinking (500 mA max.) or sourcing (250 mA max.). Z80180 9.216 MHz or 18.432 MHz. 32K standard, 512K maximum 512 bytes Up to 256K 2 RS-232 or 1 RS-232 with RTS/CTS and 1 RS-485 Up to 115,200 bps Yes Yes Yes, internal 3 V DC lithium ion

70 s Specifications

PK2200


Hardware Mechanical Dimensions
Top view for models PK2200 and PK2210.

3.09 (78.5) 2.42 (61.5) 1.85 (47.0) 0.67 (17.0) 0.37 (9.0)

help

down

del

add

init

4.85 (123.2) 4.39 (111.5)

field

4.35 (110.5)

item

menu

setup

F2

F3

run

10-32 clr, 4x

F1

1.15 (29.2) 1.11 (28.2)

0.2 typ (5) 4.0 (101)

Figure B-1. Top View PK2200 and PK2210

PK2200

Specifications s 71

0.31 typ (7.9)

5.5 (140)

up

F4


Top view for model PK2240.
1.75 (44.5) 1.455 (37.0) 1.105 (28.1) 1.262 (32.1) 0.37 (9.4)

9

6

3 2 1

1.350 (34.3)

8

5

7

4

4.85 (123.2)

­

0

.

2.719 (69.1)

3.750 (95.3)

0.621 (15.8)

10-32 clr, 4x

0.2 typ (5) 4.0 (102)

Figure B-2. Top View PK2240

72 s Specifications

PK2200

0.31 typ (7.9)

4.88 (124.0)

5.5 (139.7)


End view for models PK2200, PK2210 and PK2240.

1.71 (43.4) 1.2 (30.5)

Figure B-3. End View PK2200, PK2210, and PK2240

The board dimensions are 4.0"â5.32" overall. The centers of the mounting holes are inset (0.220", 0.770") from the corners of the board. They are 2.46" and 4.88" on center. Mounting holes are 0.160" in diameter.

PK2200

Specifications s 73

0.55 (14.0) 0.2 (5.1)

0.75 (19.1) 0.22 (5.6)
2.95 (75.0) 1.44 (36.6)


Top view of models PK2220 and PK2230.
0.030 (0.76) 0.220 (5.59) 0 .470 (11.9) 5.100 (129.5) 5.320 (135.1)
R 0.125 X 4 (3.2) R 0.125 X 4 (3.2) 0.200 (5.1) 0.770 (19.6) 3.230 (82.0) 3.800 (96.5) 4.000 (101.6)

Figure B-4. Top View PK2220 and PK2230

74 s Specifications

PK2200


High Voltage Driver Specifications
Table B-2. Sinking Driver Specifications
Parameter Absolute Maximum Rating at 25C

Output Voltage Output Current Power Dissipation (Change) Power Dissipation (Package) C-E Saturation Voltage (max.) Derating Factor

50 V DC 500 mA 1.0 W 2.25 W 1 .3 V 18.18 mW/C above 25 C

Table B-3. Sourcing Driver Specifications
Parameter Absolute Maximum Rating

Output Voltage Output Current Power Dissipation (Chan) Power Dissipation (Package) C-E Saturation Voltage (maximum) Derating Factor

30V DC 250 mA 1.0 W 2.2 W 1.2 V 18 mW/C above 25C

Environmental Temperature Constraints
No special precautions are necessary over the range of 0°C to 50°C (32°F to 122°F). For operation at temperatures below 0°C, the PK2200 should be equipped with a low temperature LCD that is specified for operation down to 20°C. The heating effect of the power dissipated by the unit may be sufficient to keep the temperature above 0°C, depending on the enclosures insulating capability. The LCD storage temperature is 20°C lower than its operating temperature, which may protect the LCD in case the power should fail, thus removing the heat source. The LCD unit is specified for a maximum operating temperature of 50°C. Except for the LCD, which fades at higher temperatures, the PK2200 operates at 60°C or more without problem.

!
PK2200

External loads and expansion cards can increase power consumption.
Specifications s 75


Connectors
Only a single, solid conductor should be placed in a screw clamp terminal. Bare copper, particularly if exposed to the air for a long period before installation, can become oxidized. The oxide can cause a high resistance (~20 ) connection, especially if the clamping pressure is not sufficient. To avoid this, use tinned wires or clean, shiny copper wire. If you are using multiple conductors or stranded wire, consider soldering the wire bundle or using a crimp connector to avoid a loss of contact pressure to a spontaneous rearrangement of the wire bundle at a latter time. Soldering may make the wire subject to fatigue failure at the junction with the solder if there is flexing or vibration.

Header Locations and Jumper Settings
Figure B-5 illustrates the location of the headers on the PK2200. Table B-4 lists each header and explains possible pin connections.

LED
JP6,1

JP1
1 3 2 4

LCD Interface

JP2

JP3

H1 PLC Bus Connector

H2

JP4 H3 Keypad Conn. CN1 CN2

JP5

Figure B-5 PK2200 Jumpers and Headers

76 s Specifications

PK2200


Table B-4. Headers and Jum per Settings
Header Pins Description

JP1 1­3, 2­4 1­2, 3­4 JP2 1 3 3 3 3 ­3 ­5 ­5 ­5 ­5 , , , , , 2 2 4 4 4 ­4 ­4 ­6 ­6 ­6

Sink/sou the jump Connect Connect

rce ers for for

con are the the

trol. The drivers will be damaged if set incorrectly. ULN2803 sinking drivers (default). UDN2985A sourcing drivers.

7­9 9­11 8­10 10­12 JP3 1­2 3-­4 5­6, 9­11 7­8 5­6, 7­8, 9­11
5­7, 11­13

EPROM flash EPROM 32K 64K 128K 128K 256K 256K 512K Input pullup/pulldown resistors Inputs 1­4 and 9­12 are pulled up. Inputs 1­4 and 9­12 are pulled down. Inputs 5­8 and 13­16 are pulled up. Inputs 5­8 and 13­16 are pulled down. M iscellaneous Enables the watchdog timer (default). Allo ws the CTS line to reset the board. Serial Comm unication One 5-wire RS-232 channel (Z180 Port 0) with RTS/CTS One 3-wire RS-232 One RS-485 channel (Port 1) One 5-wire RS-232 FD One RS-485 Two 3-wire RS-232 channels SRAM sizing 32K or 128K SRAM (default) 512K SRAM Readable jumper equivalent to mode-setting keypad keys. JP 4 overrides the keypad if jumper installed. P laces unit in program mode at 19,200 bps. Runs the program . P laces unit in program mode at 28,800 bps. indicates to Dynamic C that watchdog timer is enabled. Connect when JP 3:1-2 is installed. Write protect the EEPROM . Write-enable the EEPROM . EP ROM flash EP ROM
Specifications 77

10­12 12­14 JP4 7­8 6­7 2­3 4­5 JP5 JP 6 1­2 2­3 1­2 2­3

PK2200


Blank

78 s Specifications

PK2200


APPENDIX C: POWER MANAGEMENT
Appendix C provides information about power management and hardware and software specific to power management on the PK2200.

PK2200

Power Management s 79


Power Failure Detection Circuitry
Figure C-1 shows the power failure detection circuitry of the PK2200.
DCIN R1 +5V IC691 /PFI R2 /PFO /RES U11 /RESET R4 Microprocessor U15 /NMI D6

D6

3B

3Y D6

74HC257 U18

Figure C-1. PK2200 Power-Fail Circuit

Power Failure Sequence of Events
The following events occur as the input power fails:. 1. The 691 power-management IC first triggers a power-failure /NMI (non-maskable interrupt) when the unregulated DC input voltage falls below approximately 7.9 V (as determined by the voltage divider R1/ R2). 2. At some point, the raw input voltage level will not exceed the required regulated voltage level by the regulators dropout voltage whereupon the regulated output begins to droop. 3. The 691 next triggers a system reset when the regulated +5 V supply falls below 4.75 V, allowing your power-failure routine the holdup interval, tH, to store your important state data. 4. The 691 forces the chip enable of the SRAM high (standby mode). 5. The time/date clock and SRAM switches to the lithium backup battery when the regulated voltage falls below the battery voltage of approximately 3 V. 6. The 691 keeps the reset asserted until the regulated voltage drops below 1 V. 7. At this point the 691 ceases operating. By this time, the portion of the circuitry not battery-backed has long since ceased functioning.

80 s Power Management

PK2200


The ratio of your power supplys output capacitor s value to your circuits current draw determines the actual duration of the holdup-time interval, t .
H

Power Fails

9.0 8.0 7.0 6.0 5.0 4.0

Unregulated DC Regulated +5V
Dropout Voltage

C 3.0 2.0
Slope = C/-I

I

VOLTS

1.0 TIME
691 Asserts PFO
t
H

691 Asserts RESET

691 Ceases Operation

Figure C-2. Power Fail Sequence of Events

This setup can fail when multiple power fluctuations happen rapidly a common occurrence in the real world. If the PK2200s Z180 processor receives multiple /NMIs, it overwrites an internal register, making a correct return from the first /NMI impossible. Also, depending on the number of fluctuations of the raw DC input (and hence, the number of stacked /NMIs), the processor s stack could overflow, corrupting your programs code or data. When the Z180 senses an NMI, it saves the program counter (PC) on its processor stack. It copies the maskable interrupt flag, IEF1, to IEF2 and zeroes IEF1. The Z180 restores IEF2s saved state information when it executes a RETN (Return from Nonmaskable Interrupt) instruction.

PK2200

Power Management s 81


Recommended Power Fail Routine
Z-World recommends the following routines to handle an NMI. The routines monitor the state of the /PFO line, via U18 and the data bus, to determine if the brownout condition is continuing or if the power has returned to normal levels. If you use one of these routines, you need not worry about multiple power-failure /NMIs because these routines never return from the first /NMI unless the power returns.
Program C-1. Suggested Power Fail Routine

main(){ ... } ... char dummy[24]; ... #define NMI_BIT 3 #define NMI PIODB2

// reserve dummy stack // for /NMI processing

// routine will test data // bit 3 to determine // state of /NMI line #JUMP_VEC NMI_VEC myint #asm myint:: ld sp,dummy+24 ; force stack pointer ; to top of "dummy" ; array to prevent ; overwriting of code ; or data ;do whatever service, within allowable ;executuin time loop: call hitwd ; make sure no ; watchdog reset ; during brownout ; load the read-NMI ld bc,NMI ; register to bc in a,(c) ; read the read-NMI ; register to /PFO bit NMI_BIT, a ; check /PFO status jr z,loop ; wait until brownout ; condition clears timeout: ; then... a tight loop ; to force a watchdog ; timeout jp timeout ; which will reset the ; Z180 #endasm
82 s Power Management PK2200


The watchdog timer should be enabled. However, if the watchdog is not enabled, you can force the processor to restart execution at 0x0000. Substitute this section for the one labeled timeout above.
Program C-2. Alternate Power Fail Code

restart: ld a,0 xe2

out0 (CB AR),a jp 000 0h

; ; ; ; ; ; ;

make sure 0x0000 points to start of EPROM BIOS set the CBAR jump to logical (physical) address 0x0000

#endasm

If the DC input voltage continues to decrease, the controller powers down. The routine calls hitwd to make sure that watchdog does not timeout and thereby reset the processor. The controller can continue to run, after a fashion, at low voltage and might not be able to detect the low voltage condition, because the Z180s /NMI input needs to see a high-tolow transition edge. A situation similar to a brownout occurs if the power supply is overloaded. For example, when an LED turns on, the raw voltage supplied to the PK2200 may dip below 7.9 V. The interrupt routine does a shutdown, which turns off the LED, clearing the problem. However, if the cause of the overload persists, the system oscillates, alternately experiencing an overload and then resetting. To correct this situation, use a power supply which can provide the needed current and voltage. A few milliseconds of computing time remain when the regulated +5 V supply falls below 4.75 V, even if power cuts off abruptly. The amount of time depends on the size of the capacitors in the power supply. The standard wall power supply provides about 10 ms. If you remove the power cable abruptly from the PK2200 side, only the capacitors on the board are available, reducing computing time to a few hundred microseconds. These times can vary considerably depending on systems configuration and loads on the 5 V or 9 V supplies. The interval between the power failure detection and entry to the powerfailure interrupt routine is approximately 100 µs or less if Dynamic C NMI communication is not in use.

PK2200

Power Management s 83


Blank

84 s Power Management

PK2200


APPENDIX D: INTERRUPT VECTORS AND

I/O ADDRESSES

Appendix D provides a suggested interrupt vector map and information on EEPROM address, processor I/O addresses, and peripheral addresses.

PK2200

Interrupts and Addresses s D-85


Most of the following interrupt vectors can be altered under program control. The addresses are given in hex, relative to the start of the interrupt vector page, as determined by the contents of the I-register. These are the default interrupt vectors set by the boot code in the Dynamic C EPROM.

Interrupt Vectors
To vector an interrupt to a user function in Dynamic C, a directive such as the following is used:
#INT_VEC 0x10 myfunction

The above example causes the interrupt at offset 10H (serial port 1 of the Z180) to invoke the function myfunction(). The function must be declared with the interrupt keyword:
interrupt myfunction() { ... }

Table D-1. Z180 Internal Device Interrupt Vectors
Address Name Description

0x00 0x02 0x04 0x06 0x08 0x0A 0x0C 0x0E 0x10

INT1_VEC INT2_VEC PRT0_VEC PRT1_VEC DMA0_VEC DMA1_VEC CSIO_VEC SER0_VEC SER1_VEC

Expansion bus attention /INT1 vector /INT2 vector PRT timer channel 0 PRT timer channel 1 DMA channel 0 DMA channel 1 Clocked Serial I/O Asynchronous Serial Port Channel 0 Asynchronous Serial Port Channel 1

Digital input 11 connects to /INT0 and digital input 12 connects to /INT2, allowing external events to generate interrupts.

D-86 s Interrupts and Adresses

PK2200


Jump Vectors
These special interrupts occur in a different manner: instead of loading the address of the interrupt routine from the interrupt vector, these interrupts cause a jump directly to the address of the vector, which contains a jump instruction to the interrupt routine. For example,
0x66 non-maskable power-failure interrupt

Because nonmaskable interrupts can be used for Dynamic C communication, your interrupt vector for power failure is normally stored just in front of the Dynamic C program. You can store a vector there by using the following command:
#JUMP_VEC NMI_VEC name

The Dynamic C communication routines relay to this vector when a power failure causes the NMI rather than a serial interrupt. Table D-2 lists interrupt priorities from the highest to lowest priority.
Table D-2. Interrupt Priorities
Interrupt Priorities

(Highest Priority)

Trap (Illegal Instruction) NMI (Nonmaskable Interrupt) INT 0 (Maskable Interrupt, Level 0, 3 modes, PIO interrupts) INT 1 (Maskable Interrupt, Level 1, PLCBus attention line interrupt) INT 2 (Maskable Interrupt, Level 2) PRT Timer Channel 0 PRT Timer Channel 1 DMA Channel 0 DMA Channel 1 Clocked Serial I/O Serial Port 0

(Lowest Priority)

Serial Port 1

PK2200

Interrupts and Addresses s D-87


EEPROM Addresses
These EEPROM constants apply to the standard PK2200.
Table D-3. Z180 I/O Device Register Addresses
Address Description

0x000 0x001 0x100

Startup Mode. If 1, enter program mode. If 8, execute loaded program at startup. Baud rate in units of 1200 baud. Unit "serial number." BCD time and date with the following format: second, minutes, hours, day, month, year. Microprocessor clock speed in units of 1200 Hz (16bits). For 9.216 MHz clock speed, this value is 7680. For 18.432 MHz, this value is 15,360. Long coefficient relating speed of microprocessor clock relative to speed of real-time clock. Nominal value is 107,374,182 which is 1/40 of a second microprocessor clock time on the scale where 232 is 1 second. This value requires 4 bytes of EEPROM, stored least byte first.

0x108

0x16C

D-88 s Interrupts and Adresses

PK2200


Processor Register Addresses
The Z180s I/O-device registers occupy the first 40 addresses.
H

Table D-4. Z180 Internal I/O Device Registers
Address Name Description

0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F 0x10 0x11­13 0x14 0x15 0x16 0x17 0x18 0x19­1E 0x1F

CNTLA0 CNTLA1 CNTLB0 CNTLB1 STAT0 STAT1 TDR0 TDR1 RDR0 RDR1 CNTR TRDR

Serial Channel 0, Control Register A Serial Channel 1, Control Register A Serial Channel 0, Control Register B Serial Channel 1, Control Register B Status Register, Serial Channel 0 Status Register, Serial Channel 1 Transmit Data Register, Serial Channel 0 Transmit Data Register, Serial Channel 1 Receive Data Register, Serial Channel 0 Receive Data Register, Serial Channel 1 Clocked Serial Control Register Clocked Serial Data Register Timer Data Register, Channel 0, low Timer Data Register, Channel 0, high Timer Reload Register, Channel 0, low Timer Reload Register, Channel 0, high Timer Control Register Reserved Timer Data Register, Channel 1, low Timer Data Register, Channel 1, high Timer Reload Register, Channel 1, low Timer Reload Register, Channel 1, high Free-Running Counter Reserved CPU control register for the 18 MHz chip. Write 0x80 to get 18.432 MHz. Write 0 to get 9.216 MHz. DMA Source Address, Channel 0, low

TMDR0L
TMDR0H RLDR0L RLDR0H TCR -- TMDR1L TMDR1H RLDR1L RLDR1H FRC -- CCR

0x20

SAR0L

continued...

PK2200

Interrupts and Addresses s D-89


Table D-4. Z180 Internal I/O Device Registers (concluded)
Ad dress Nam e Description

0x21 0x22 0 x2 3 0 x2 4 0x25 0x26 0x27 0 x2 8 0x29 0 x2 A 0 x2 B 0 x2 C 0x2D 0x2E 0x2F 0x30 0x31 0x32 0 x3 3 0 x3 4 0x35 0x36 0x37 0x38 0 x3 9 0x3A 0x3B­3D 0x3E 0 x3 F

SAR0H SAR0B D AR 0 L D AR 0 H DAR0B BCR0L BCR0H M AR 1 L M AR1H M AR 1 B IAR1L IAR1H -- BCR1L BCR1H DSTAT DM ODE DCNTL IL ITC -- RCR -- CBR BBR CBAR -- OM CR ICR

DM A Source Address, Channel 0, high DM A Source Address, Channel 0, extra bits DM A Destination Address, Channel 0, low DM A Destination Address, Channel 0, most Destination Address, Channel 0, extra bits DM A Byte Count Register, Channel 0, low DM A Byte Count Register, Channel 0, high DM A Memory Address Register, Channel 1, low DM A Memory Address Register, Channel 1, high DM A Memory Address Register, Channel 1, extra bits DM A I/O Address Register, Channel 1, low DM A I/O Address Register, Channel 1, high Reserved DM A Byte Count Register, Channel 1, low DM A Byte Count Register, Channel 1, high DM A Status Register DM A Mode Register DM A/WAIT Control Register Interrupt V ector Low Register Interrupt/Trap Control Register Reserved Refresh Control Register Reserved M M U Common Base Register M M U Bank Base Register M M U Common/Bank Area Register Reserved Operation M ode Control Register I/O Control Register

D-90 s Interrupts and Adresses

PK2200


PK2200 Peripheral Addresses
The following addresses control the I/O devices that are external to the Z180 processor.
Table D-5. PK2200 External I/O Device Registers
Address Bit(s) Symbol Function

0x40

7

WDOG

Watchdog is "hit" (when JP3:1-2) by setting bit 7 of this address. Turns on LED by setting bit 7 of this address. Turn off by clearing bit 7. EEPROM clock bit. Set the clock high by setting bit 7 of this address, and low by clearing bit 7. EEPROM serial data, write. Send data in bit 7. First read, PLC expansion bus Second read, PLC expansion bus Spare read, PLC expansion bus Read this address to reset all devices on expansion bus PLC expansion bus, first address byte PLC expansion bus, second address byte PLC expansion bus, third address byte Expansion bus write to port LCD read/write register, control LCD read/write register, data

0x60

7

LED

0x80

7

SCL

0xA0 0xC0 0xC2 0xC4 0xC6 0xC8 0xCA 0xCC 0xCE 0xE0 0xE1

7 0­7 0­7 0­7 -- 0­7 0­7 0­7 0­7 0­7 0­7

SDA_W BUSRD0 BUSRD1 BUSSPARE BUSRESET BUSADR0 BUSADR1 BUSADR2 BUSWR LCDRD LCDWR LCDRD+1 LCDWR+1

continued...

PK2200

Interrupts and Addresses s D-91


Table D-5. PK2200 External I/O Device Registers (continued)
Address Bit(s) Symbol Function

0x100 0x120 0x140

0­3 0­3 7

RTALE RTRW BUZZER

Real-time clock, address register Real-time clock, read/write data register Self-resonating buzzer. Set bit 7 to turn on. Clear bit 7 to turn off. Set bit 7 to enable RS-485 channel. Clear bit 7 to disable. Digital Input, Bank 1. Bit 0 corresponds to input 1; bit 7 corresponds to input 8. Digital Input, Bank 2. Bit 0 corresponds to input 9; bit 7 corresponds to input 16. Keypad drive row 1, rightmost 4 keys. Bit 4 is rightmost key. Bit 5 is key next to that, etc. Row 1 is the bottom-most row. Keypad drive row 2, rightmost 4 keys. Bit 4 is rightmost key. Bit 5 is key next to that, etc. If there were support for a 4â6 keypad, this would be drive row 3. As of now, it reads jumper JP4. As of now, this address is reserved. Keypad, all rows, rightmost 4 keys. Bit 4 is rightmost key. Bit 5 is key next to that, etc. Row 1 is the bottom-most row. Bit 7 represents the EEPROM SDA line. Bit 6 presents the power-failure (NMI) state.

0x160 0x180

7 0­7

ENB485 DIGBANK1

0x181

0­7

DIGBANK2

0x1A1

4­7

KROW1L

0x1A2

4­7

KROW2L

0x1A4

4­7

KROW3L

0x1A8 0x1AF

4­7 4­7

KROW4L KROWAL

0x1B0

6-7

SDA_R NMI

continued...

D-92 s Interrupts and Adresses

PK2200


Table D-5. PK2200 External I/O Device Registers (continued)
Address Bit(s) Symbol Function

0x1B1

4­7

KROW1H

Keypad drive row 1, keys. Bit 5 is leftmo key next to that. Bit EEPROM SDA line. power-failure (NMI) is bottom-most row.

leftmost 2 st key. Bit 4 is 7 represents Bit 6 presents state. Row 1

0x1B 2

4­7

KROW2H

Keypad drive row 2, leftmost 2 keys. Bit 5 is leftmost key. Bit 4 is next. Bit 7 represents EEPROM SDA line. Bit 6 presents powerfailure (NMI) state. If there were support for a 4â6 keypad, this would be drive row 3. As of now, bits 4 and 5 are reserved. Bit 7 is EEPROM SDA line. Bit 6 presents power-failure (NMI) state. If there were support for a 4â6 keypad, this would be drive row 4. As of now, bits 4 and 5 are reserved. Bit 7 represents EEPROM SDA line. Bit 6 is power-failure (NMI) state. Keypad, all rows, leftmost 2 keys. Bit 5 is the leftmost key. Bit 4 is the key next to that. Bit 7 represents the EEPROM SDA line. Bit 6 presents the power-failure (NMI) state. Row 1 is the bottommost row. Digital output 1. Writing 0x20 turns on output. Writing 0 turns off output. Digital output 2. Writing 0x20 turns on output. Writing 0 turns off output. Digital output 3. Writing 0x20 turns on output. Writing 0 turns off output.

0x1B4

4­7

KROW3H

0x1B8

4­7

KROW4H

0x1BF

4­7

KROWAH

0x1C0

5

DRV1

0x1C1

5

DRV2

0x1C2

5

DRV3

continued...

PK2200

Interrupts and Addresses s D-93

continued . . .


Table D-5. PK2200 External I/O Device Registers (concluded)
Address Bit(s) Symbol Function

0x1C3

5

DRV4

Digital output 4. Writing 0x20 turns on output. Writing 0 turns off output. Digital output 5. Writing 0x20 turns on output. Writing 0 turns off output. Digital output 6. Writing 0x20 turns on output. Writing 0 turns off output. Digital output 7. Writing 0x20 turns on output. Writing 0 turns off output. Digital output 8. Writing 0x20 turns on output. Writing 0 turns off output. Digital output 9. Writing 0x40 turns on Outputs. Writing 0 turns off Outputs. Digital Outputs 10. Writing 0x40 turns on output. Writing 0 turns off output. Digital output 11. Writing 0x40 turns on output. Writing 0 turns off output. Digital output 12. Writing 0x40 turns on output. Writing 0 turns off output. Digital output 13. Writing 0x40 turns on output. Writing 0 turns off output. Digital output 14. Writing 0x40 turns on output. Writing 0 turns off output.

0x1C4

5

DRV5

0x1C5

5

DRV6

0x1C6

5

DRV7

0x1C7

5

DRV8

0x1E0

6

DRV9

0x1E1

6

DRV10

0x1E2

6

DRV11

0x1E3

6

DRV12

0x1E4

6

DRV13

0x1E5

6

DRV14

D-94 s Interrupts and Adresses

PK2200


APPENDIX E: PLCBUS
Appendix E provides the pin assignments for the PLCBus, describes the registers, and lists the software drivers.

PK2200

PLCBus s 95


PLCBus Overview
The PLCBus is a general-purpose expansion bus for Z-World controllers. The PLCBus is available on the BL1200, BL1600, BL1700, PK2100, PK220, and PK2600 controllers. The BL1000, BL1100, BL1300, BL1400, and BL1500 controllers support the XP8300, XP8400, XP8600, and XP8900 expansion boards using the controller s parallel input/output port. The BL1400 and BL1500 also support the XP8200 and XP8500 expansion boards. The ZB4100s PLCBus supports most expansion boards, except for the XP8700 and the XP8800. The SE1100 adds relay expansion capability to all controllers through their digital outputs. Table E-1 lists Z-Worlds expansion devices that are supported on the PLCBus.
Table E-1. Z-World PLCBus Expansion Devices
Device Description

EXP-A/D12 SE1100 XP8100 Series XP8200 XP8300 XP8400 XP8500 XP8600 XP8700 XP8800 XP8900

Eight channels of 12-bit A/D converters Four SPDT relays for use with all Z-World controllers 32 digital inputs/outputs "Universal Input/Output Board" --16 universal inputs, 6 high-current digital outputs Two high-power SPDT and four high-power SPST relays Eight low-power SPST DIP relays 11 channels of 12-bit A/D converters Two channels of 12-bit D/A converters One full-duplex asynchronous RS-232 port One-axis stepper motor control Eight channels of 12-bit D/A converters
GND A0X LCDX D1X D3X D5X D7X GND GND GND GND +24 V (+5 V) VCC
26 24 22 20 18 16 14 12 10 8 6 4 2 25 23 21 19 17 15 13 11 9 7 5 3 1

Multiple expansion boards may be linked together and connected to a Z-World controller to form an extended system. Figure E-1 shows the pin layout for the PLCBus connector.

VCC (+5 V) /RDX /WRX D0X D2X D4X D6X A1X A2X A3X strobe /STBX attention /AT GND

Figure E-1. PLCBus Pin Diagram 96 s PLCBus PK2200


Two independent buses, the LCD bus and the PLCBus, exist on the single connector. The LCD bus consists of the following lines. LCDXpositive-going strobe. /RDXnegative-going strobe for read. /WRXnegative-going strobe for write. A0Xaddress line for LCD register selection. D0X-D7Xbidirectional data lines (shared with expansion bus).

The LCD bus is used to connect Z-Worlds OP6000 series interfaces or to drive certain small liquid crystal displays directly. Figure E-2 illustrates the connection of an OP6000 interface to a controller PLCBus.
Yellow wire on top

PLCBus Header
Note position of connector relative to pin 1.

From OP6000 KLB Interface Card Header J2 Pin 1
Figure E-2. OP6000 Connection to PLCBus Port

The PLCBus consists of the following lines. /STBXnegative-going strobe. A1XA3Xthree control lines for selecting bus operation. D0XD3Xfour bidirectional data lines used for 4-bit operations. D4XD7Xfour additional data lines for 8-bit operations. /ATattention line (open drain) that may be pulled low by any device, causing an interrupt.

The PLCBus may be used as a 4-bit bus (D0XD3X) or as an 8-bit bus (D0XD7X). Whether it is used as a 4-bit bus or an 8-bit bus depends on the encoding of the address placed on the bus. Some PLCBus expansion cards require 4-bit addressing and others (such as the XP8700) require 8-bit addressing. These devices may be mixed on a single bus.

PK2200

PLCBus s 97


There are eight registers corresponding to the modes determined by bus lines A1X, A2X, and A3X. The registers are listed in Table E-2.
Table E-2. PLCBus Registers
Register Address A3 A2 A1 Meaning

BUSRD0 BUSRD1 BUSRD2 BUSRESET BUSADR0 BUSADR1 BUSADR2 BUSWR

C0 C2 C4 C6 C8 CA CC CE

0 0 0 0 1 1 1 1

0 0 1 1 0 0 1 1

0 1 0 1 0 1 0 1

Read data, one way Read data, another way Spare, or read data Read this register to reset the PLCBus First address nibble or byte Second address nibble or byte Third address nibble or byte Write data

Writing or reading one of these registers takes care of all the bus details. Functions are available in Z-Worlds software libraries to read from or write to expansion bus devices. To communicate with a device on the expansion bus, first select a register associated with the device. Then read or write from/to the register. The register is selected by placing its address on the bus. Each device recognizes its own address and latches itself internally. A typical device has three internal latches corresponding to the three address bytes. The first is latched when a matching BUSADR0 is detected. The second is latched when the first is latched and a matching BUSADR1 is detected. The third is latched if the first two are latched and a matching BUSADR2 is detected. If 4-bit addressing is used, then there are three 4-bit address nibbles, giving 12-bit addresses. In addition, a special register address is reserved for address expansion. This address, if ever used, would provide an additional four bits of addressing when using the 4-bit convention. If eight data lines are used, then the addressing possibilities of the bus become much greatermore than 256 million addresses according to the conventions established for the bus.

98 s PLCBus

PK2200


Place an address on the bus by writing (bytes) to BUSADR0, BUSADR1 and BUSADR2 in succession. Since 4-bit and 8-bit addressing modes must coexist, the lower four bits of the first address byte (written to BUSADR0) identify addressing categories, and distinguish 4-bit and 8-bit modes from each other. There are 16 address categories, as listed in Table E-3. An x indicates that the address bit may be a 1 or a 0.
Table E-3. First-Level PLCBus Address Coding
First Byte ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ x x x x 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 Mode 4 bits â 3 Addresses 256 256 256 256 2,0 2,0 2,0 2,0 48 48 48 48 0 0 0 0 Full Address Encoding 000 001 010 011 10 10 11 11 0 1 0 1 xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxx xxx xxx xxx xx xx xx xx

5 bits â 3

x0 x0 x0 x0

xxxxx xxxxx xxxxx xxxxx

­­xx1000 ­­xx1001 ­­xx1010 ­­­­1011 xxxx1100 xxxx1101 xxxx1110 xxxx1111

6 bits â 3 6 bits â 1 4 bits â 1 8 bits â 2 8 bits â 3 8 bits â 1 8 bits â 1

16,384 16,384 4 1 4,096 1M 16 16

xx1000 xxxxxx xxxxxx xx1001 xxxxxx xxxxxx xx1010 1011 (expansion register) xxxx1100 xxxxxxxx xxxx1101 xxxxxxxx xxxxxxxx xxxx1110 xxxx1111

This scheme uses less than the full addressing space. The mode notation indicates how many bus address cycles must take place and how many bits are placed on the bus during each cycle. For example, the 5 â 3 mode means three bus cycles with five address bits each time to yield 15-bit addresses, not 24-bit addresses, since the bus uses only the lower five bits of the three address bytes.

PK2200

PLCBus s 99


Z-World provides software drivers that access the PLCBus. To allow access to bus devices in a multiprocessing environment, the expansion register and the address registers are shadowed with memory locations known as shadow registers. The 4-byte shadow registers, which are saved at predefined memory addresses, are as follows.
SHBUS0 Bus expansion SHBUS0+1 BUSADR0 SHBUS1 SHBUS0+2 BUSADR1 SHBUS1+1 SHBUS0+3 BUSADR2

Before the new addresses or expansion register values are output to the bus, their values are stored in the shadow registers. All interrupts that use the bus save the four shadow registers on the stack. Then, when exiting the interrupt routine, they restore the shadow registers and output the three address registers and the expansion registers to the bus. This allows an interrupt routine to access the bus without disturbing the activity of a background routine that also accesses the bus. To work reliably, bus devices must be designed according to the following rules. 1. The device must not rely on critical timing such as a minimum delay between two successive register accesses. 2. The device must be capable of being selected and deselected without adversely affecting the internal operation of the controller.

Allocation of Devices on the Bus
4-Bit Devices
Table E-4 provides the address allocations for the registers of 4-bit devices.
Table E-4. Allocation of Registers
A1 A2 A3 Meaning

000j 000j 000j 000j 000j 001j

000j 001j 01xj 10xj 11xj xxxj

xxxj xxxj xxxj xxxj xxxj xxxj

digital output registers, 64 registers 64 â 8 = 512 1-bit registers analog output modules, 64 registers digital input registers, 128 registers 128 â 4 = 512 input bits analog input modules, 128 registers 128 spare registers (customer) 512 spare registers (Z-World)

j x
100 s PLCBus

controlled by board jumper
controlled by PAL
PK2200


Digital output devices, such as relay drivers, should be addressed with three 4-bit addresses followed by a 4-bit data write to the control register. The control registers are configured as follows bit 3 A2 bit 2 A1 bit 1 A0 bit 0 D

The three address lines determine which output bit is to be written. The output is set as either 1 or 0, according to D. If the device exists on the bus, reading the register drives bit 0 low. Otherwise bit 0 is a 1. For digital input, each register (BUSRD0) returns four bits. The read register, BUSRD1, drives bit 0 low if the device exists on the bus.

8-Bit Devices
Z-Worlds XP8700 and XP8800 expansion boards use 8-bit addressing. Refer to the XP8700 and XP8800 manual.

Expansion Bus Software
The expansion bus provides a convenient way to interface Z-Worlds controllers with expansion boards or other specially designed boards. The expansion bus may be accessed by using input functions. Follow the suggested protocol. The software drivers are easier to use, but are less efficient in some cases. Table E-5 lists the libraries.
Table E-5. Dynamic C PLCBus Libraries
Library Needed Controller

DRIVERS.LIB EZIOTGPL.LIB EZIOLGPL.LIB EZIOMGPL.LIB EZIOPLC.LIB EZIOPLC2.LIB PBUS_TG.LIB PBUS_LG.LIB PLC_EXP.LIB

All controllers BL1000 BL1100 BL1400, BL1500 BL1200, BL1600, PK2100, PK2200, ZB4100 BL1700, PK2600 BL1000 BL1100, BL1300 BL1200, BL1600, PK2100, PK2200

PK2200

PLCBus s 101


There are 4-bit and 8-bit drivers. The 4-bit drivers employ the following calls. void eioResetPlcBus() Resets all expansion boards on the PLCBus. When using this call, make sure there is sufficient delay between this call and the first access to an expansion board. LIBRARY: EZIOPLC.LIB, EZIOPLC2.LIB, EZIOMGPL.LIB. void eioPlcAdr12( unsigned addr ) Specifies the address to be written to the PLCBus using cycles BUSADR0, BUSADR1, and BUSADR2. PARAMETER: addr is broken into three nibbles, and one nibble is written in each BUSADRx cycle. LIBRARY: EZIOPLC.LIB, EZIOPLC2.LIB, EZIOMGPL.LIB. void set16adr( int adr ) Sets the current address for the PLCBus. All read and write operations access this address until a new address is set. PARAMETER: adr is a 16-bit physical address. The high-order nibble contains the value for the expansion register, and the remaining three 4-bit nibbles form a 12-bit address (the first and last nibbles must be swapped). LIBRARY: DRIVERS.LIB. void set12adr( int adr ) Sets the current address for the PLCBus. All read and write operations access this address until a new address is set. PARAMETER: adr is a 12-bit physical address (three 4-bit nibbles) with the first and third nibbles swapped. LIBRARY: DRIVERS.LIB. void eioPlcAdr4( unsigned addr ) Specifies the address to be written to the PLCBus using only cycle BUSADR2. PARAMETER: addr is the nibble corresponding to BUSADR2. LIBRARY: EZIOPLC.LIB, EZIOPLC2.LIB, EZIOMGPL.LIB.

102 s PLCBus

PK2200


void set4adr( int adr ) Sets the current address for the PLCBus. All read and write operations access this address until a new address is set. A 12-bit address may be passed to this function, but only the last four bits will be set. Call this function only if the first eight bits of the address are the same as the address in the previous call to set12adr. PARAMETER: adr contains the last four bits (bits 811) of the physical address. LIBRARY: DRIVERS.LIB. char _eioReadD0( ) Reads the data on the PLCBus in the BUSADR0 cycle. RETURN VALUE: the byte read on the PLCBus in the BUSADR0 cycle. LIBRARY: EZIOPLC.LIB, EZIOPLC2.LIB, EZIOMGPL.LIB. char _eioReadD1( ) Reads the data on the PLCBus in the BUSADR1 cycle. RETURN VALUE: the byte read on the PLCBus in the BUSADR1 cycle. LIBRARY: EZIOPLC.LIB, EZIOPLC2.LIB, EZIOMGPL.LIB. char _eioReadD2( ) Reads the data on the PLCBus in the BUSADR2 cycle. RETURN VALUE: the byte read on the PLCBus in the BUSADR2 cycle. LIBRARY: EZIOPLC.LIB, EZIOPLC2.LIB, EZIOMGPL.LIB. char read12data( int adr ) Sets the current PLCBus address using the 12-bit adr, then reads four bits of data from the PLCBus with BUSADR0 cycle. RETURN VALUE: PLCBus data in the lower four bits; the upper bits are undefined. LIBRARY: DRIVERS.LIB.

PK2200

PLCBus s 103


char read4data( int adr ) Sets the last four bits of the current PLCBus address using adr bits 8 11, then reads four bits of data from the bus with BUSADR0 cycle. PARAMETER: adr bits 811 specifies the address to read. RETURN VALUE: PLCBus data in the lower four bits; the upper bits are undefined. LIBRARY: DRIVERS.LIB. void _eioWriteWR( char ch) Writes information to the PLCBus during the BUSWR cycle. PARAMETER: ch is the character to be written to the PLCBus. LIBRARY: EZIOPLC.LIB, EZIOPLC2.LIB, EZIOMGPL.LIB. void write12data( int adr, char dat ) Sets the current PLCBus address, then writes four bits of data to the PLCBus. PARAMETER: adr is the 12-bit address to which the PLCBus is set.
dat (bits 03) specifies the data to write to the PLCBus.

LIBRARY: DRIVERS.LIB. void write4data( int address, char data ) Sets the last four bits of the current PLCBus address, then writes four bits of data to the PLCBus. PARAMETER: adr contains the last four bits of the physical address (bits 811).
dat (bits 03) specifies the data to write to the PLCBus.

LIBRARY: DRIVERS.LIB. The 8-bit drivers employ the following calls. void set24adr( long address ) Sets a 24-bit address (three 8-bit nibbles) on the PLCBus. All read and write operations will access this address until a new address is set. PARAMETER: address is a 24-bit physical address (for 8-bit bus) with the first and third bytes swapped (low byte most significant). LIBRARY: DRIVERS.LIB.

104 s PLCBus

PK2200


void set8adr( long address ) Sets the current address on the PLCBus. All read and write operations will access this address until a new address is set. PARAMETER: address contains the last eight bits of the physical address in bits 1623. A 24-bit address may be passed to this function, but only the last eight bits will be set. Call this function only if the first 16 bits of the address are the same as the address in the previous call to set24adr. LIBRARY: DRIVERS.LIB. int read24data0( long address ) Sets the current PLCBus address using the 24-bit address, then reads eight bits of data from the PLCBus with a BUSRD0 cycle. RETURN VALUE: PLCBus data in lower eight bits (upper bits 0). LIBRARY: DRIVERS.LIB. int read8data0( long address ) Sets the last eight bits of the current PLCBus address using address bits 1623, then reads eight bits of data from the PLCBus with a BUSRD0 cycle. PARAMETER: address bits 1623 are read. RETURN VALUE: PLCBus data in lower eight bits (upper bits 0). LIBRARY: DRIVERS.LIB. void write24data( long address, char data ) Sets the current PLCBus address using the 24-bit address, then writes eight bits of data to the PLCBus. PARAMETERS: address is 24-bit address to write to.
data is data to write to the PLCBus.

LIBRARY: DRIVERS.LIB. void write8data( long address, char data ) Sets the last eight bits of the current PLCBus address using address bits 1623, then writes eight bits of data to the PLCBus. PARAMETERS: address bits 1623 are the address of the PLCBus to write.
data is data to write to the PLCBus.

LIBRARY: DRIVERS.LIB.

PK2200

PLCBus s 105


Blank

106 s PLCBus

PK2200


APPENDIX F: BACKUP BATTERY

PK2200

Backup Battery s 107


Battery Life and Storage Conditions
The ten-year estimated life of a battery on the PK2200 is based on typical use. Most systems are operated on a continuous basis with the battery only powering the SRAM and real time clock during power outages and/ or routine maintenance. A ten-year life expectancy is an estimate that reflects the shelf-life of a lithium battery with occasional usage rather than the ability of the battery to power the circuitry full time. The battery on the PK2200 has a 165 mA·h capacity. Older versions of the PK2200 have a Toshiba clock that consumes 8 µA in idle mode. Newer boards have an Epson clock that consumes 3 µA in idle mode. In standby mode, SRAM consumes from a low of 1 µA (32K SRAM) to a high of 8 µA (512K SRAM). If a system were unpowered 100 percent of the time, the battery life with a Toshiba clock will be approximately 18,300 hours (2.1 years), and with an Epson clock will be approximately 41,250 hours (4.7 years). All life-expectancy ranges are based on normal operating temperatures of 25°C. Backup time longevity is affected by many factors, including the amount of time the controller is not powered, and the SRAM size. To help achieve a full ten years of backup, a larger capacity cell can replace the BR2325. Alkaline batteries (mounted external to the board, like in many PCs) can easily and cheaply give over ten years of backup. The controller should be stored at room temperature in the factory packaging until field installation. Take care that the controller is not exposed to extreme temperature, humidity, and/or contaminants such as dust and chemicals. To ensure maximum battery shelf life, follow proper storage procedures. Replacement batteries should be kept sealed in the factory packaging at room temperature until installation. Protection against environmental extremes will help maximize battery life.

Replacing Soldered Lithium Battery
Use the following steps to replace the battery. 1. Locate the three pins on the bottom side of the printed circuit board that secure the battery to the board. 2. Carefully de-solder the pins and remove the battery. Use a solder sucker to clean up the holes. 3. Install the new battery and solder it to the board. Use only a Panasonic BR2325-1GM or equivalent.

108 s Backup Battery

PK2200


Battery Cautions
w

Caution (English) There is a danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer s instructions.

w

Warnung (German) Explosionsgefahr durch falsches Einsetzen oder Behandein der Batterie. Nur durch gleichen Typ oder vom Hersteller empfohlenen Ersatztyp ersetzen. Entsorgung der gebrauchten Batterien gemÄb den Anweisungen des Herstellers.

w

Attention (French) Il y a danger dexplosion si la remplacement de la batterie est incorrect. Remplacez uniquement avec une batterie du mÉme type ou dun type Èquivalent recommandÈ par le fabricant. Mettez au rebut les batteries usagÈes conformÈment aux instructions du fabricant.

w

Cuidado (Spanish) Peligro de explosiÑn si la pila es instalada incorrectamente. Reemplace solamente con una similar o de tipo equivalente a la que el fabricante recomienda. Deshagase de las pilas usadas de acuerdo con las instrucciones del fabricante.

w

Waarschuwing (Dutch) Explosiegevaar indien de batterij niet goed wordt vervagen. Vervanging alleen door een zelfde of equivalent type als aanbevolen door de fabrikant. Gebruikte batterijen afvoeren als door de fabrikant wordt aangegeven.

w

Varning (Swedish) ExplosionsfÄra vid felaktigt batteribyte. AnvÄnd samma batterityp eller en likvÄrdigt typ som rekommenderas av fabrikanten. Kassera anvÄnt batteri enligt fabrikantens instruktion.

PK2200

Backup Battery s 109


Blank

110 s Backup Battery

PK2200


INDEX
Symbols
#INT_VEC ........................... 41, 86 #JUMP_VEC ................................ 87

attention line .............................. 97 attention line interrupt ................ 87

/AT ............................................. 97 /DREQ1 ..................................... 26 /INT0 ......................................... 26 /INT2 ......................................... 26 /RDX .......................................... 97 /STBX ........................................ 97 /WRX ......................................... 97 ................................... 20 =(assignment) use ...................... 68 _DMAFLAG0 ................................ 53 _DMAFLAG1 ................................ 53 4-bit bus operations ... 97, 98, 100 5 â 3 addressing mode ............... 99 5KEYCODE.C ............................. 62 5KEYDEMO.C ............................. 62 5KEYLAD.C ................................ 62 8-bit bus operations ... 97, 99, 101 9th-bit binary protocol ............... 63

B
background routine .................. 100 battery backup .................................... 80 replacing .............................. 108 baud rate ............................. 29, 88 BBR ........................................... 89 BCR0H ...................................... 89 BCR0L ....................................... 89 BCR1H ...................................... 89 BCR1L ....................................... 89 beeper sounding ................................. 55 bidirectional data lines ............... 97 bitmapped graphics .................... 47 bitmaps ....................................... 47 board dimensions ....................... 73 board jumpers ............................ 34 brownout .................................... 83 buffer receive ............................. 38, 39 transmit .................................. 38 bus control registers ................... 101 digital inputs ........................ 101 expansion 96, 97, 98, 99, 100, 101 4-bit drivers ..................... 102 8-bit drivers ..................... 104 addresses .......................... 100 devices .................... 100, 101 functions 102, 103, 104, 105 rules for devices ............... 100 software drivers ............... 101 LCD ....................................... 97

A
A0X ........................................... A1X, A2X, A3X ................. 97, addresses digital input ............................ EEPROM ............................... encoding ................................. I/O register ............................. modes ..................................... peripheral I/O ......................... PLCBus ........................... 98, ASCII characters and modem commands .......... asynchronous serial port Channel 0 ............................... Channel 1 ...............................
PK2200

97 98 52 88 99 89 99 91 99 39 86 86

Index s 111


bus (continued) operations 4-bit .................... 97, 98, 100 8-bit ........................... 97, 101 BUSADR0 ................... 91, 98, 99 BUSADR1 ................... 91, 98, 99 BUSADR2 ................... 91, 98, 99 BUSADR3 ...................... 104, 105 BUSRD0 91, 101, 102, 103, 105 BUSRD1 .................. 91, 101, 102 BUSRESET ............................... 91 BUSSPARE ............................... 91 BUSWR ............................ 91, 102 BUZZER .................................... 91 byte aligned ................................ 47

COMMAND mode modem communication .......... common problems programming errors ............... communication Dynamic C ............................. error ....................................... initialization routines ............. RS-232 ............................ 29, RS-485 ............................ 29, serial ........................ 29, 38, interrupts ............................
Compile

39 68 87 19 40 63 63 63 38 20 20 18 76 96 88 23 36 53 53 23 86 63 40 63 15 63

C
calibration constants .................. 88 carriage return (CR) as modem command terminator . ........................................... 39 CBAR ........................................ 89 CBR ........................................... 89 CCR ........................................... 89 CE compliance ........................... 16 CKA0/DREQ0 ........................... 26 clock real time ................................. 86 real-time .......................... 88, 91 system ............................. 29, 88 time/date ................................ 50 clock frequency system .................................... 88 clocked serial control register .... 89 clocked serial data register ........ 89 clocked serial I/O ................ 86, 87 CN2 ............................................ 26 CNTLA0 .................................... 89 CNTLA1 .................................... 89 CNTLB0 .................................... 89 CNTLB1 .................................... 89 CNTR ........................................ 89 column major ............................. 47
112 s Index

icon ........................................ program .................................. connect PK2200 to PC .............. connectors ........................... 42, 26-pin PLCBus pin assignments .................. constants calibration .............................. core ............................................ counters ............................... 26, DMA ...................................... inputs .............................. 36, CPU ........................................... CSIO_VEC .................................. CSREMOTE.C ............................. CTS .............................. 38, 39, CUARTREM.C ............................. customization ............................. CZ0REM.C ..................................

D
D0XD7X .................................. DAR0B ...................................... DAR0L ...................................... DATA mode modem communication .......... date and time ................ 50, 63, DCNTL ...................................... Development Kit ........................ DIGBANK1 ............................... 97 89 89 39 88 89 15 91

PK2200


DIGBANK2 ............................... 91 digital inputs ......... 24, 26, 36, 62 drivers .................................... 52 reading ................................... 52 multiple inputs ................... 52 virtual driver variables ........... 52 digital outputs ....... 27, 37, 54, 91 drivers .................................... 52 virtual driver variables ........... 54 writing .................................... 54 Dinit_uart ............................. 40 Dinit_z0 .................................. 40 Dinit_z1 .................................. 40 DIP relays .................................. 96 display ................................. 31, 43 liquid crystal. See LCD dissipation heat ........................................ 75 DMA .......................................... 89 DMA channels ............. 26, 36, 53 DMA Channel 0 .............. 86, 87 DMA Channel 1 .............. 86, 87 DMA counter ............................. 53 DMA interrupts .......................... 53 DMA/WAIT ............................... 89 DMA0_VEC .................................. 86 DMA1_VEC .................................. 86 DMA0Count ................................ 53 DMA1Count ................................ 53 DMASnapShot ........................... 53 DMODE .................................... 89 downloading data ................ 38, 39 downloading programs .............. 41 drivers digital input ............................ 52 digital output .......................... 52 expansion bus ...................... 101 4-bit .................................. 102 8-bit .................................. 104 high voltage ........................... 27 relay ..................................... 101 sinking .................................... 27 software ................................. 50 sourcing ................................. 28
PK2200

DRIVERS.LIB ......................... 101

dropout voltage .......................... DRV10 ....................................... DRV11 ....................................... DRV4 ......................................... DRV5 ......................................... DRV6 ......................................... DRV7 ......................................... DRV8 ......................................... DRV9 ......................................... DSTAT ....................................... DTR ........................................... Dynamic C communication ...................... error messages ....................... programming ..........................

80 91 91 91 91 91 91 91 91 89 40

87 19 34

E
echo option ......................... 38, 39 edges counting ................................. 37 ee_rd ........................................ 51 ee_wr ........................................ 51 EEPROM ..................... 24, 51, 91 constants ................................ 86 reading ................................... 51 writing .................................... 51 EEPROM adresses ..................... 88 eioPlcAdr12 ......................... 102 eioReadD0 .............................. 103 eioReadD1 .............................. 103 eioReadD2 .............................. 103 eioResetPlcBus ................... 102 eioWriteWR ........................... 104 electrical and environmental specifications ..................... 70 ENB485 ..................................... 91 environmental constraints .......... 75 EPROM ..................................... 36 error messages .................... 19, 20 establishing communication ....... 19 Exp-A/D12 ................................. 96

Index s 113


expansion boards reset ...................................... 102 expansion bus .... 86, 87, 91, 96101 4-bit drivers ......................... 102 8-bit drivers ......................... 104 addresses .............................. 100 devices ........................ 100, 101 digital inputs ........................ 101 functions ...................... 102105 rules for devices ................... 100 software drivers ................... 101 expansion register .................... 100 EZIOLGPL.LIB ....................... 101 EZIOMGPL.LIB ....................... 101 EZIOPL2.LIB ......................... 101 EZIOPLC.LIB ......................... 101 EZIOTGPL.LIB ....................... 101

glPlotLine ............................. glPrintf .................................. glPutBitmap ........................... glPutFont ................................ glSetBrushType ..................... glVPrintf ................................ glXFontInit ........................... glXPutBitmap .........................

57 60 57 59 56 59 59 58

H
halt program ............................... handshaking RS-232 ................................... Hayes Smart Modem ................. headers ....................................... heat dissipation .......................... high-current output drivers ........ high-voltage drivers ................... holdup time ................................ hooking up the PK2200 ............. 20 38 40 76 75 22 27 81 19

F
F3 ............................................... 20 F9 ............................................... 20

features ....................................... 12 five-key system sample program ..................... 62 flash EPROM ............................. 36
float

I
I/O addresses ...................... 89, 91 I/O control register ..................... 89 I/O devices ................................. 91 I/O map ............................... 89, 91 I/O register addresses ................ 89 IAR1H ....................................... 89 IAR1L ........................................ 89 ICR ............................................ 89 IL ............................................... 89 illegal instruction interrupt ......... 87 initial PK2200 setup .................. 34 initialization routines communication ...................... 40 inport ........... 52, 102, 103, 105 inputs counter ................................... 53 digital ................ 24, 26, 36, 62 inserts keypad .................................... 44
int

use .......................................... fonts .................................... 58, format bitmapped image .................... FRC ............................................ frequency system clock ........................... function libraries ........................

68 59 47 89 88 98

G
getting started ............................ glBlankScreen ....................... glFontInit ............................. glInit ...................................... glPlotCircle ......................... glPlotDot ................................ 17 57 58 57 60 57

type specifier, use .................. 68
PK2200

114 s Index


INT1 .......................................... 87 INT1_VEC .................................. 86 INT2 .......................................... 87 INT2_VEC .................................. 86 interface operator .................................. 31 interrupt handling for Z180 Port 0 .. 41 interrupt routines ................. 83, 87 interrupt vector CSIO_VEC .............................. 86 DMA0_VEC .............................. 86 DMA1_VEC .............................. 86 INT1_VEC .............................. 86 INT2_VEC .............................. 86 PRT0_VEC .............................. 86 PRT1_VEC .............................. 86 SER0_VEC .............................. 86 SER1_VEC .............................. 86 interrupt vector low register ....... 89 interrupt vectors ......................... 87 default .................................... 86 interrupt/trap control register ..... 89 interrupts .... 26, 36, 86, 87, 97, 100 attention line .......................... 87 DMA ...................................... 53 illegal instruction ................... 87 nonmaskable ................... 83, 87 power-fail ................. 80, 83, 87 routines ................................ 100 serial ............................... 41, 87 serial communication ............. 38 T0 output ............................... 87 ITC ............................................. 89

K
kdiELSw .................................... 60 kdiSetContrast ..................... 60

keypad ................... 31, 34, 55, 2 x 6 ....................................... 4 x 3 ....................................... initialization ............. 55, 61, mode settings ......................... reading ............................ 61, states ...................................... keypad inserts ............................ KP.LIB ...................................... kpDefGetKey ........................... kpDefInit ................................ kpDefStChgFn ......................... kpInit ...................................... kpScanState ........................... KROW1L .................................. KROW2L .................................. KROW3L .................................. KROW4L .................................. KROWAL ..................................

91 34 35 62 34 62 61 44 55 62 62 61 61 61 91 91 91 91 91

L
lc_char .................................... lc_cmd ...................................... lc_ctrl .................................... lc_init .................................... lc_init_keypad ..................... lc_kxget .................................. lc_kxinit ................................ lc_nl ........................................ lc_pos ...................................... lc_printf ................................ lc_setbeep ............................. lc_wait ....................................

J
jumper settings ............. 34, 77, JP1 (digital outputs) ........ 28, JP2 (digital inputs) .......... 25, JP3 (run/program mode) . 34, JP3 (serial communication) . 30, JP4 (run/program mode) ........ JP5 (EEPROM write-protect) JP6 (EPROM/flash EPROM)
PK2200

86 77 77 35 77 77 77 77

LCD ...................... 46, 55, 91, backlighting ........................... busy ........................................ character ................................ graphic ................................... backlighting ....................... clear display .......................
Index

55 56 56 56 55 55 55 56 56 56 55 56 97 43 56 43 43 60 57
115


LCD graphic (continued) contrast .............................. 60 drawing ......... 56, 57, 58, 60 font initialization ......... 58, 59 initialization ....................... 57 turning display ON/OFF .... 60 writing ......................... 59, 60 initialization ........................... 56 positioning text ...................... 56 writing ............................. 55, 56 commands .......................... 56 LCD bus ..................................... 97 LCDRD ...................................... 91 LCDWR ..................................... 91 LCDX ........................................ 97 leap year ..................................... 50 LED .................................... 83, 91 libraries function .................................. 98 liquid crystal display. See LCD literal (C term) use .......................................... 68 lithium battery .......................... 108

modes addressing .............................. 99 operating ................................ 34

N
NMI ...................... 80, 83, 87, NMI_VEC .................................... NO_CARRIER message ............ nonmaskable interrupt. See NMI NULL modem ............................ 91 87 39 40

O
OMCR ....................................... 89 operating modes ......................... 34 operation mode control register ... 89 operator interface ....................... 31 Opto22 9th-bit binary protocol .... 63 outport ......... 54, 102, 103, 105 outputs digital ................ 27, 37, 54, 91 overload protection .................... 24

P
peripheral I/O addresses ............ 91 pinouts PLCBus .................................. 96 PK2200 connect to PC ......................... 18 establish communication ........ 19 features ................................... 12 hook-up .................................. 19 subsystems ............................. 21 PLCBus ............. 86, 87, 91, 9698, 100, 101 26-pin connector pin assignments .................. 96 4-bit operations ............... 97, 99 8-bit operations ............... 97, 99 addresses ......................... 98, 99 memory-mapped I/O register . 98 reading data ........................... 98

M
MAR1B ..................................... 89 MAR1H ..................................... 89 MAR1L ...................................... 89 master-slave communication ...... 63 mechanical dimensions ........ 7174 MMU bank base register ........... 89 MMU common base register ..... 89 MMU common/bank area register . ........................................... 89 mode startup .................................... 88 MODEM ............................. 38, 39 modem commands ..................... 39 termination ............................. 39 modem communication ....... 41, 63 serial link wiring .................... 40

116 s Index

PK2200


PLCBus (continued) relays DIP ..................................... 96 drivers .............................. 101 writing data ............................ 98 ports serial ...................................... 38 power failure detection ................................ 80 interrupts .................. 80, 83, 87 recommended routine ............ 82 power management .................... 79 power supply ....................... 18, 83 overload ................................. 83 program run .......................................... 20 program development ................ 35 programming remote .................................... 41 programming cable .................... 18 protected digital inputs .............. 22 protocol 9th-bit binary ......................... 63 Opto22 ................................... 63 XMODEM ...................... 38, 39 PRT timer Channel 0 ........................ 86, 87 Channel 1 ........................ 86, 87 PRT0_VEC .................................. 86 PRT1_VEC .................................. 86 pulse measurement ..................... 37

R
RAM ................................... 23, 35 RCR ........................................... 89 RDR0 ......................................... 89 RDR1 ......................................... 89 read12data ........................... 103 read24data ........................... 105 read4data .............................. 104 read8data .............................. 105 reading data on the PLCBus .......... .................................. 98, 103
PK2200

real-time clock .... 24, 50, 86, 88, 91 reading ................................... 50 writing .................................... 50 real-time kernel .......................... 62 receive buffer ...................... 38, 39 receive data register ................... 89 refresh control register ............... 89 regulated input voltage .............. 80 RELOAD_VEC ............................. 41 remote downloading ........... 41, 63 reset controller ................................ 19 expansion boards ................. 102 system .................................... 80 RLDR0H .................................... 89 RLDR0L .................................... 89 RLDR1H .................................... 89 RLDR1L .................................... 89 RS-232 ................................ 29, 38 communication ...................... 63 expansion card ......... 38, 39, 40 handshaking ........................... 38 jumper settings ....................... 30 RS-485 ....................................... 29 channel ................................... 91 communication ...................... 63 jumper settings ....................... 30 network .................................. 42 RTALE ....................................... 91 RTK ........................................... 62 RTRW ........................................ 91 RTS .............................. 38, 39, 40 RX line ....................................... 40

S
sample program .................. 20, SAR0B ....................................... SAR0H ....................................... SAR0L ....................................... SCL ............................................ screw terminals ................... 42, SDA_R ....................................... SDA_W ..................................... 62 89 89 89 91 76 91 91

Index s 117


SE1100 ....................................... 96 select PLCBus address ............. 102 SER0_VEC ........................... 41, 86 SER1_VEC .................................. 86 Serial Channel 0 control register B ................... 89 receive data register ............... 89 status register ......................... 89 transmit data register .............. 89 Serial Channel 1 control register A ................... 89 control register B ................... 89 receive data register ............... 89 status register ......................... 89 transmit data register .............. 89 serial channels configuring ............................. 30 serial communication ... 29, 38, 63 channels ................................. 22 serial interrupts ................... 41, 87 serial link wiring ........................ 40 Serial Port 0 ............................... 87 Serial Port 1 ............................... 87 serial ports ................................. 38 set12adr ................................ 102 set16adr ................................ 102 set24adr ................................ 104 set4adr .................................. 103 set8adr .................................. 105 shadow registers ....................... 100 sinking drivers ........................... 27 software drivers .................................... 50 libraries ........................... 62, 98 source (C term) use .......................................... 68 sourcing drivers ......................... 28 specifications ............................. 69 electrical and environmental .. 70 stack overflow ............................ 81 standby mode ............................. 80 startup mode .............................. 88

STAT0 ........................................ STAT1 ........................................ struct tm ................................ supervisor .................................. system clock ............................... frequency ........................ 29,

89 89 50 23 88 88

T
T0 output interrupt ..................... 87 target not responding ................. 19 TCR ........................................... 89 TDR0 ......................................... 89 TDR1 ......................................... 89 templates keypad insert .......................... 44 text displaying on graphic LCD ........ .................................... 59, 60 time and date ................ 50, 63, 88 time/date clock ........................... 50 timer control register ................. 89 timer data register Channel 0 ............................... 89 Channel 1 ............................... 89 timer reload register Channel 0 ............................... 89 Channel 1 ............................... 89 tm ............................................... 50 tm_rd ........................................ 50 tm_wr ........................................ 50 TMDR0H ................................... 89 TMDR0L ................................... 89 TMDR1H ................................... 89 TMDR1L ................................... 89 transmit buffer ............................ 38 transmit data register .................. 89 trap ............................................. 87 TRDR ........................................ 89 troubleshooting baud rate ................................ 67 cables ..................................... 66 com port .......................... 66, 67

118 s Index

PK2200


troubleshooting (continued) communication mode ............. expansion boards ................... grounds .................................. memory size ........................... operating mode ...................... repeated resets ....................... TX line .......................................

67 66 66 67 67 67 40

write12data ......................... write24data ......................... write4data ........................... write8data ...........................

104 105 104 105 writing data on the PLCBus ... 98, 104 wtDisplaySw ........................... 60

X
XMODEM .......................... 38, 39 XMODEM download ................ 63 XMODEM upload ..................... 63 XP8100 ...................................... 96 XP8200 ...................................... 96 XP8300 ...................................... 96 XP8400 ...................................... 96 XP8500 ...................................... 96 XP8600 ...................................... 96 XP8700 ...................... 96, 97, 101 XP8800 ............................. 96, 101 XP8900 ...................................... 96

U
UDN2985A ......................... 27, ULN2803 ................................... unregulated input voltage ........... up_beep .................................... up_digin .................................. up_setout ................................ uploading data .................... 38, 28 27 80 55 52 54 39

V
VIOInit .................................... 52 VIODrvr .................................... 52

Z
Z180 Port 0 .......................... 3841 interrupt handling ................... 41 Z180 Port 1 ......................... 38, 86

W
watchdog .................................... 23 WDOG ....................................... 91 WINTEK.LIB ............................. 55

PK2200

Index s 119


Blank


SCHEMATICS

PK2200