Документ взят из кэша поисковой машины. Адрес оригинального документа : http://www.naic.edu/~phil/hardware/12meter/Doc/ThirdParty/EmersonCT/Unimotor_FM_product_data.pdf
Дата изменения: Sat Aug 23 17:52:00 2008
Дата индексирования: Sat Feb 12 13:43:09 2011
Кодировка:
Поисковые слова: annular solar eclipse

Product Data 055 to 190 Frames
0.72 Nm to 73.2 Nm

www .controltechniques.com

055-190 Unimotor
Introducing the 055 to 190 frames.

Product Data

is a range of brushless AC ser vo motors which support a winding to suit 200/240V or 400/480V nominal AC drives such as the , Unidrive classic and Digitax ST range of drives. The range is available in six frame sizes 055:075:095:115:142 and 190mm, each frame size has a number of shaft diameter options and can offer various front flange mounting arrangements. The 190 frame motor has been increased in variants from 4 (A-D) to 8 (A-H). The design also conforms to the sealing standard IP65 (when mounted and connected).

Standard Features
* * * * * * * * * * Modular rotor design. Rotor assembly balanced to ISO1940 ( BS 6861 ) G 6.3. Incremental encoder for high precision feedback. PTC thermistors for thermal monitoring and overload protection. IP65 standard; sealed against water spray and dust. (IP65 mating connectors must be used) Vertical connectors for power and signal. Low inertia is standard for fast acceleration. UL and cUL recognised motors (075-190 frame motors only). E21543 IEC mounting flange. Shaft key as standard.

Optional Features
* * * * * * * * * * * * * Parking brake. High energy dissiptation brake. 90° fixed or 90° rotatable connectors. A range of shaft diameters. Optional IEC and NEMA flanges available. High inertia. Other Incremental encoder interfaces available. Resolver feedback for rugged applications. Sin/Cos encoder for high resolution and accuracy (single and multi-turn). Other interfaces available. NEMA mounting available. Plain shaft (non keyed). Electronic name plating (Available on Sincos motors only). (075-190 frame motors only). IP 54 rated motors (055 only).

Optional Products
* Cable assemblies for power and signal. (Compliant to DESINA standard) * Where volumes have justified it, Control Techniques have designed a number of custom specific motors. Please contact your Drive Centre or Distributor for details. * Gearbox options, high precision low backlash or general purpose, parallel shaft or right angle gearboxes available in various ratios.

2

Dimensions (mm) Frame size 055

NOTE: Output key dimensions (E, F, G and H) are applicable to keyed units only. H (h9) C (j6)

D F G

B2 max B1 max

4 holes R(H14) equispaced on a S PCD K Flange For vertical connectors, allow approximately 175.0mm clearance for mating cable

L ma x Optional key N

P Motor flange

M (j6) Tapped hole thread size I to depth J

E

A ma x T Motor housing

Standard Motor Dimension (mm) Note: All dimensions shown are at maximum
UNBRAKED Length A 055A 118.0 055B 055C 142.0 166.0 B1 48.0 72.0 96.0 B2 56.0 80.0 A 158.0 182.0 BRAKED Length B1 88.0 112.0 136.0 B2 96.0 120.0 144.0 9.0 2.5 40.0 96.0 55.0 5.8 63.0 55.0 FLANGE THICKNESS K REGISTER LENGTH L REGISTER DIAMETER M (j6) OVERALL HEIGHT N FLANGE SQUARE P SFIXING HOLE DIAMETER R (H14) FIXING HOLE PCD S MOTOR HOUSING T

104.0 206.0

Vertical connectors dimension (mm) Note: All dimensions shown are at maximum
Unbraked Length B1 055A 055B 055C 75.0 99.0 123.0 B2 83.0 107.0 131.0 Braked Length B1 B2 Power Connector N 104.0 104.0 104.0 Signal Connector N 93.0 93.0 93.0

115.0 123.0 139.0 147.0 163.0 173.0

Shaft Diameter (mm)
SHAFT DIAMETER SHAFT LENGTH KEY HEIGHT KEY LENGTH KEY TO SHAFT END KEY WIDTH TAPPED HOLE THREAD SIZE TAPPED HOLE DEPTH

C (j6) 9.0 11.0 14.0 9.0 11.0 14.0

D 20.0 23.0 30.0

E 11.1 13.4 16.9

F 15.8 18.8 25.8

G 1.5 1.2 1.2

H (h9) 3.0 4.0 4.0

I M4 M4 M5

J 12.5 12.5 15.0

Optional connector height (mm)
C type V type 96.0 105.0

3

055-190 Unimotor
Dimensions (mm) Frame size 075
NOTE: Output key dimensions (E, F, G and H) are applicable to keyed units only. C (j6) H (h9) D F G B max

Product Data

4 holes R(H14) equispaced on a mounting PCD S L m ax Optional key
P Motor flange

K Flange For vertical connectors, allow approximately 175.0mm clearance for mating cable

N M (j6) E

T Motor housing

Tapped hole thread size I to depth J

A ma x

Standard Motor Dimension (mm) Note: All dimensions shown are at maximum
UNBRAKED Length A 075A 075B 075C 075D 209.1 239.1 269.1 299.1 B 158.2 188.2 218.2 248.2 A 254.1 284.1 314.1 344.1 BRAKED Length B 203.2 233.2 263.2 293.2 6.3 2.5 60.0 119.5 70.2 6.1 75.4 75.5 M5 FLANGE THICKNESS K REGISTER LENGTH L REGISTER DIAMETER M (j6) OVERALL HEIGHT VERTICAL N FLANGE SQUARE P FIXING HOLE DIAMETER R (H14) FIXING HOLE PCD S MOTOR HOUSING T MOUNTING BOLTS

Optional flange motor dimensions (mm)
UNBRAKED LENGTH A 075A 075B 075C 075D 193.5 223.5 253.5 283.5 B 142.6 172.6 202.6 323.6 A 238.5 268.5 298.5 328.5 BRAKED LENGTH B 187.6 217.6 247.6 277.6

Optional flange dimensions (mm)
FIXING HOLE PCD S 66.7 80.0 85.0 REGISTER DIAMETER M 60 +0/-0.05 60 70 M5 M5 M6 MOUNTING BOLTS

Optional connector height (mm)
CONNECTION TYPE A B C OVERALL HEIGHT N 119.0 127.0 127.0

Shaft Diameter (mm)
SHAFT DIAMETER SHAFT LENGTH KEY HEIGHT KEY LENGTH KEY TO SHAFT END KEY WIDTH TAPPED HOLE THREAD SIZE TAPPED HOLE DEPTH

C (j6) 11.0 A Std 14.0 B-D Std 19.0 Max 11 14 19

D 23.5 30.5 40.5

E 12.9 16.3 21.8

F 14.3 22.3 32.3

G 4.8 4.8 4.8

H (h9) 4.0 5.0 6.0

I M4 M5 M6

J 11.4 13.9 17.4

4

Dimensions (mm) Frame size 095
NOTE: Output key dimensions (E, F, G and H) are applicable to keyed units only. G C (j6) H (h9) D F B max

4 holes R(H14) equispaced on a mounting PCD S Optional key

K Flange L max For vertical connectors, allow N approximately 175.0mm clearance for mating cable

P Motor flange

M (j6)

E

Tapped hole thread size I to depth J T Motor housing

A max

Standard Motor Dimension (mm) Note: All dimensions shown are at maximum
UNBRAKED Length A 095A 095B 095C 095D 095E 227.8 257.8 287.8 317.8 347.8 B 176.9 206.9 236.9 266.9 296.9 A 272.8 302.8 332.8 362.8 392.8 BRAKED Length B 221.9 251.9 281.9 311.9 341.9 6.4 2.9 80.0 132.5 90.2 7.0 100.4 95.6 M6 FLANGE THICKNESS K REGISTER LENGTH L REGISTER DIAMETER M (j6) OVERALL HEIGHT VERTICAL N FLANGE SQUARE P FIXING HOLE DIAMETER R (H14) FIXING HOLE PCD S MOTOR HOUSING T MOUNTING BOLTS

Optional flange motor dimensions (mm)
UNBRAKED LENGTH A 095A 095B 095C 095D 095E 202.7 232.7 262.7 292.7 322.7 B 151.8 181.8 211.8 241.8 270.8 A 247.7 277.7 307.7 337.7 367.7 BRAKED LENGTH B 196.8 226.8 256.8 286.8 316.8

Optional flange dimensions (mm)
FIXING HOLE PCD S 98.83 115.4 REGISTER DIAMETER M 73.025 +0/-0.05 95 (j6) M6 M8 MOUNTING BOLTS

Optional connector height (mm)
CONNECTION TYPE A B C OVERALL HEIGHT N 132.0 140.0 140.0

Shaft Diameter (mm)
SHAFT DIAMETER SHAFT LENGTH KEY HEIGHT KEY LENGTH KEY TO SHAFT END KEY WIDTH TAPPED HOLE THREAD SIZE TAPPED HOLE DEPTH

C (j6) 14.0 A Std 19.0 B-E Std 22.0 Max 14 19 22

D 30.5 40.5 50.5

E 16.3 22.8 24.8

F 22.3 32.3 40.3

G 4.8 4.7 5.8

H (h9) 5.0 6.0 6.0

I M5 M6 M8

J 13.9 17.4 20.4

5

055-190 Unimotor
Dimensions (mm) Frame size 115
NOTE: Output key dimensions (E, F, G and H) are applicable to keyed units only. C (j6/k6) H (h9) 4 holes R(H14) equispaced on a mounting PCD S Optional key L max D F G B max

Product Data

K Flange For vertical connectors, allow approximately 175.0mm clearance for mating cable

P Motor flange

N M (j6) E

T Motor housing

Tapped hole thread size I to depth J

A max

Standard Motor Dimension (mm) Note: All dimensions shown are at maximum
UNBRAKED Length A 115A 115B 115C 115D 115E 246.1 276.1 306.1 336.1 366.1 B 203.0 233.0 263.0 293.0 323.0 A 291.1 321.1 351.1 381.1 411.1 BRAKED Length B 248.0 278.0 308.0 338.0 368.0 10.1 2.9 95.0 150.0 105.2 10.0 115.4 115.6 M8 FLANGE THICKNESS K REGISTER LENGTH L REGISTER DIAMETER M (j6) OVERALL HEIGHT VERTICAL N FLANGE SQUARE P FIXING HOLE DIAMETER R (H14) FIXING HOLE PCD S MOTOR HOUSING T MOUNTING BOLTS

Optional flange dimensions (mm) Optional flange motor dimensions (mm)
UNBRAKED LENGTH A 115A 115B 115C 115D 115E 215.3 245.3 275.3 305.3 335.3 B 172.2 202.2 232.2 262.2 292.2 A 260.3 290.3 320.3 350.3 380.3 BRAKED LENGTH B 217.2 247.2 277.2 307.2 337.2 A B C FIXING HOLE PCD S 126.1 130.4 145.0 REGISTER DIAMETER M 110 +0/-0.05 110 (j6) 110 (h7) M8 M8 M8 MOUNTING BOLTS

Optional connector height (mm)
CONNECTION TYPE OVERALL HEIGHT N 149.5 157.5 157.5

Shaft Diameter (mm)
SHAFT DIAMETER SHAFT LENGTH KEY HEIGHT KEY LENGTH KEY TO SHAFT END KEY WIDTH TAPPED HOLE THREAD SIZE TAPPED HOLE DEPTH

C 19.0 A-C std 22.0 Opt 24.0 D-E Std 28.0 Opt 32.0 Max 19 (j6) 22 (j6) 24 (j6) 28 (j6) 32 (k6)

D 40.4 50.4 50.4 60.4 80.4

E 21.8 24.8 27.3 31.3 35.3

F 32.3 40.3 40.3 50.3 70.3

G 4.8 5.8 5.7 5.8 5.8

H (h9) 6.0 6.0 8.0 8.0 10.0

I M6 M8 M8 M10 M12

J 17.4 20.4 20.4 23.4 29.4

6

Unimotor
Dimensions (mm) Frame size 142
NOTE: Output key dimensions (E, F, G and H) are applicable to keyed units only. G C (j6/k6) H (h9) 4 holes R(H14) equispaced on a mounting PCD S K Flange L max Optional key N M (j6) E For vertical connectors, allow approximately 175.0mm clearance for mating cable D F B max

P Motor flange

Tapped hole thread size I to depth J T Motor housing

A max

Standard Motor Dimension (mm) Note: All dimensions shown are at maximum
UNBRAKED Length A 142A 142B 142C 142D 142E 227.1 257.1 287.1 317.1 347.1 B 184.0 214.0 244.0 274.0 304.0 A 272.1 302.1 332.1 362.1 392.1 BRAKED Length B 229.0 259.0 289.0 319.0 349.0 12.1 3.6 130.0 177.0 142.2 12.0 165.4 142.7 M10 FLANGE THICKNESS K REGISTER LENGTH L REGISTER DIAMETER M (j6) OVERALL HEIGHT VERTICAL N FLANGE SQUARE P FIXING HOLE DIAMETER R (H14) FIXING HOLE PCD S MOTOR HOUSING T MOUNTING BOLTS

Optional flange motor dimensions (mm)
UNBRAKED LENGTH A 142A 142B 142C 142D 142E 277.3 307.3 337.3 367.3 397.3 B 234.2 264.2 294.2 324.2 354.2 A 322.3 352.3 382.3 412.3 442.3 BRAKED LENGTH B 279.2 309.2 339.2 369.2 399.2

Optional flange dimensions (mm)
FIXING HOLE PCD S 149.23 REGISTER DIAMETER M 114.3 +0/-0.076 M8 MOUNTING BOLTS

Optional connector height (mm)
CONNECTION TYPE A B C OVERALL HEIGHT N 177.0 184.5 184.5

Shaft Diameter (mm)
SHAFT DIAMETER SHAFT LENGTH KEY HEIGHT KEY LENGTH KEY TO SHAFT END KEY WIDTH TAPPED HOLE THREAD SIZE TAPPED HOLE DEPTH

C 22.0 Opt 24.0 A-E Std 28.0 Opt 32.0 Max 22 (j6) 24 (j6) 28 (j6) 32 (k6)

D 50.5 50.5 60.5 80.5

E 24.8 27.3 31.1 35.3

F 40.3 40.3 50.3 70.3

G 5.8 5.8 5.8 5.8

H (h9) 6.0 8.0 8.0 10.0

I M8 M8 M10 M12

J 20.4 20.4 23.4 29.4

7

055-190 Unimotor
Dimensions (mm) Frame size 190
NOTE: Output key dimensions (E, F, G and H) are applicable to keyed units only. C (k6) H (h9) D F G

Product Data
B max

4 holes R(H14) equispaced on a mounting PCD S

K Flange L max

P Motor flange

Optional key M (j6) E

For vertical connectors, allow N approximately 175.0mm clearance for mating cable

Tapped hole thread size I to depth J T Motor housing

A max

Standard Motor Dimension (mm) Note: All dimensions shown are at maximum
UNBRAKED Length A 190A 190B 190C 190D 190E 190F 190G 190H 238.3 265.2 292.2 319.1 346.1 373.0 400.0 426.9 B 199.2 226.1 253.1 280.0 307.0 333.9 360.9 387.8 A 319.1 346.1 373.0 400.0 426.9 453.9 480.8 507.8 BRAKED Length B 280.0 307.0 333.9 360.9 387.8 414.8 441.7 468.7 15.5 4.0 180.0 233.0 190.2 14.5 215.0 191.5 M12 FLANGE THICKNESS K REGISTER LENGTH L REGISTER DIAMETER M (j6) OVERALL HEIGHT VERTICAL N FLANGE SQUARE P FIXING HOLE DIAMETER R (H14) FIXING HOLE PCD S MOTOR HOUSING T MOUNTING BOLTS

Optional connector height (mm)
CONNECTION TYPE A B C OVERALL HEIGHT N 246.0 253.5 253.5

Shaft Diameter (mm)
SHAFT DIAMETER SHAFT LENGTH KEY HEIGHT KEY LENGTH KEY TO SHAFT END KEY WIDTH TAPPED HOLE THREAD SIZE TAPPED HOLE DEPTH

C (k6) 32.0 A-H Std 38.0 Opt 42.0 Max 32 38 42

D 80.5 80.5 110.5

E 35.3 41.3 45.4

F 70.3 70.3 100.3

G 5.8 5.8 5.8

H (h9) 10.0 10.0 12.0

I M12 M12 M16

J 29.4 29.4 37.4

8

Motor Selection
Motor de-rating Any adverse operating conditions require that the motor performance be de-rated. These conditions include; ambient temperature above 40°C, motor mounting position, drive switching frequency or the drive being oversized for the motor. Ambient temperatures The ambient temperature around the motor must be taken into account. For ambient temperatures above 40°C the torque must be de-rated using the following formula as a guideline. (Note: Only applies to 2000/3000rpm motors and assumes copper losses dominate) New de-rated torque = Specified torque x

[1-( Ambient temperature -40)/(100)]

For example with an ambient temperature of 76°C the new de-rated torque will be 0.8 x specified torque. Mounting arrangements The motor torque must be de rated if the motor mounting surface is heated from an external source, such as a gearbox. The motor is connected to a poor thermal conductor. The motor is mounted with the connectors on the side or vertical. The motor is in a confined space with restricted air flow. Drive switching frequency Most Unidrive SP and Digitax ST nominal current ratings are reduced for the higher switching frequencies see the appropriate drive manual for details.

See the table below for the motor de rate factors. These figures are for guidance only.
(Note: Only applies to motors up to 3000rpm and assumes copper losses dominate)

Motor de rate factors
Motor type/frame size Switching frequency 055 A-C 3kHz 4kHz 6kHz 8kHz 12/16kHz 0.84 0.87 0.90 0.95 1 075 A-D 0.93 0.94 0.95 0.98 1 095 A-E 0.88 0.91 0.93 0.97 1 A-C 0.89 0.91 0.93 0.97 1 115 D-E 0.84 0.87 0.90 0.95 1 A-C 0.87 0.91 0.94 0.97 1 142 D-F 0.81 0.86 0.89 0.96 1 A-B 0.98 0.99 0.99 1 1 190 C-H N/A 0.55 0.77 0.90 1

Thermal test conditions The performance data shown has been recorded under the following conditions. Ambient temperature 20°C, with the motor mounted on a thermally isolated aluminum plate as shown below.

Thermal Isolator Plate

Motor Dynomometer

Motor type 055mm 075-095mm 115-142mm 190mm

Aluminium Heat 110 x 110 x 250 x 250 x 350 x 350 x 500 x 500 x

sink plate 27mm 15mm 20mm 20mm

Thermal protection Thermistor protection (145°C) is built into the motor windings and gives an indication of serious overheating problems. The installer must connect the thermistor to the drive, failure to do so will invalidate the motor warranty in respect of a burnt out winding. Environmental conditions Any liquids or gases that may come into contact with the motor must be confirmed to ensure compliance with the correct international standards.

9

055-190 Unimotor
Ordering Information

Product Data

Use the information below in the illustration to create an order code for a . The details in the band are an example of an order reference. (Std = Standard selection Opt = Optional selection).

095
Frame Size 055 075 095 115 142 190

U
Motor voltage*

2

B

30
Rated Speed*

1
Brake*

V
Connection Type* 055 Frame only B= Power and Signal 90° rotatable (Std) C = Power 90° rotatable and Signal vertical V = Power and Signal vertical X= Special 075-190 Frame only A = Power and Signal 90° fixed B = Power and Signal 90° rotatable C = Power 90° rotatable and Signal vertical V = Power and Signal vertical (Std) X = Special

Peak torque Stator selection* length * A B C D E F G H

055 Frame E = 230V only U = 400V 2 = Standard peak torque 075-142 Frame only 2 = Standard peak torque P = High peak torque 190 Frame only 2 = Standard peak torque

055 Frame only 055 Frame only 30 = 3000 rpm (Std) 0 = Not fitted (Std) 60 = 6000 rpm 1 = Parking brake fitted 24Vdc 075-190 Frame only 10 = 1000 rpm X = Special 20 = 2000 rpm 075-190 Frame only 25 = 2500 rpm 0 = Not fitted (Std) 30 = 3000 rpm (Std) 1 = Parking brake 40 = 4000 rpm fitted 24Vdc 45 = 4500 rpm 5 = High energy 50 = 5000 rpm dissipation 60 = 6000 rpm X = Special

* **

Not available on some frame sizes. Please consult Drive Centre or Distributor for details. Optional PCD's will have a different register diameter from the standard motors. Please consult Drive Centre or Distributors for details.

10

A
Output shaft

CA
Feedback device 055 Frame only Resolver Incremental Encoder Incremental Encoder Inductive Sincos Multi turn Inductive Sincos Single turn Incremental Encoder Optical Sincos Multi turn Optical Sincos Single turn Special 075-190 Frame only EC FC EB FB AE CA MA RA SA XX = = = = = = = = = = Inductive Sincos Multi turn Inductive Sincos Single turn Optical Sincos Multi turn Optical Sincos Single turn Resolver Incremental Encoder Incremental Encoder Optical Sincos Multi turn Optical Sincos Single turn Special EQI 1331 ECI 1319 EQN 1325 ECN 1313 4096 ppr 2048 ppr SRM 50 SRS 50 4096 ppr 1024 ppr

A
Inertia 055 Frame only

100
PCD***

190
Shaft Diameter***

A = Key (Std) B = Plain shaft AR = CP = X = Special KP = EM = FM = MP = TL = UL = XX =

2048 ppr SKM 36 SKS 36

063 A = Standard 070 075-190 Frame only A = Standard 075 B = High 080 Inertia 085 100 098 115 115 130 145 165 149 215

055 frame only Std 09.0 Opt Opt 11.0 A-C S 14.0 Max 075 frame only Std 11.0 A S Opt 14.0 B-D S Opt 19.0 Max 095 frame only Std 14.0 A S Opt 19.0 B-E S Opt 22.0 Max 115 frame only Std 19.0 A-C S Opt 24.0 D-E S Opt 32.0 Max 142 frame only Std 24.0 A-E S Opt 32.0 Max 190 frame only Std 32.0 A-H S 42.0 Max

td

td td

td td

td td

td

td

11

055-190 Unimotor
Unimotor
All data subject to +/-10% tolerance

Performance Data

For 3 Phase VPWM Drives 200-240Vrms

t= 100°C winding 40°C maximum ambient

Motor Frame Size (mm) Frame Length Continuous Stall Torque (Nm) Standard (2) Peak Torque selection max (Nm) High (P) Peak Torque selection max (Nm) Standard Inertia (kgcm2) High Inertia (kgcm2) Winding Thermal Time Const. (sec) Maximum Cogging (Nm) Standard motor weight unbraked (kg) Standard motor weight braked (kg) Rated Speed 2000 (rpm)
Kt (Nm/A) = Ke (V/krpm) =

055E2
A 0.72 2.75 N/A 0.12 B 1.40 5.50 N/A 0.23 C 2.11 8.25 N/A 0.34 A 1.2 3.6 6 0.7 1.1 81 0.02 3.60 4.10

075E2
B 2.2 6.6 11 1.2 1.5 74 0.03 4.40 4.90 C 3.1 9.3 15.5 1.6 2.0 94 0.04 5.20 5.70 D 3.9 11.7 19.5 2.0 2.4 100 0.05 6.00 6.50 A 2.3 6.9 10.4 1.8 3.7 172 0.03 5.10 5.70 B 4.3 12.9 19.4 2.9 4.8 168 0.06 6.30 6.90

095E2
C 5.9 17.7 26.6 4.0 5.9 183 0.08 7.50 8.70 D 7.5 22.5 33.8 5.1 7.0 221 0.10 8.70 9.30 E 9.0 27.0 40.5 6.2 8.1 228 0.13 9.90 10.50

0.03 1.20 1.60

0.05 1.50 1.90

0.07 1.80 2.20

Kt (Nm/A) = 1.40 Ke (V/krpm) = 85.50

Rated Torque (Nm) Stall Current (A) Rated Power (kW) R (ph-ph) (Ohms) L (ph-ph) (mH) Rated Speed 3000 (rpm)
Kt (Nm/A) = Ke (V/krpm) =

C/D

C/D

C/D

1.1 0.9 0.23 45.8 98.8

2.1 1.6 0.44 15.3 43.4

3.0 2.3 0.63 8.5 27.9

3.8 2.8 0.80 5.72 20.2

2.2 1.7 0.46 19.4 59.2

4.0 3.1 0.84 6.2 25.8

5.5 4.3 1.15 3.16 16.0

6.9 5.4 1.45 2.31 12.6

8.2 6.5 1.72 1.71 10.1

0.74 45.00

0.83 50.50

0.86 52.50

Kt (Nm/A) = 0.93 Ke (V/krpm) = 57.00

Rated Torque (Nm) Stall Current (A) Rated Power (kW) R (ph-ph) (Ohms) L (ph-ph) (mH) Rated Speed 4000 (rpm)
Kt (Nm/A) = Ke (V/krpm) =

0.60 0.98 0.21 30.0 67.3

1.20 1.68 0.43 14.7 43.0

1.80 2.46 0.64 9.6 30.9

1.1 1.3 0.35 18.9 42.5

2.0 2.4 0.63 6.26 18.4

2.8 3.4 0.88 3.50 11.9

3.5 4.2 1.10 2.38 8.82

2.0 2.5 0.63 8.03 25.6

3.9 4.7 1.23 2.68 12.0

5.4 6.4 1.70 1.57 7.91

6.8 8.1 2.14 1.03 5.60

8.1 9.7 2.54 0.77 4.65

Kt (Nm/A) = 0.72 Ke (V/krpm) = 44.00

Rated Torque (Nm) Stall Current (A) Rated Power (kW) R (ph-ph) (Ohms) L (ph-ph) (mH) Rated Speed 6000 (rpm)
Kt (Nm/A) = Ke (V/krpm) =

C/D

C/D

C/D

1.0 1.7 0.42 10. 2 24. 6

1.7 3.1 0.71 3. 39 10. 8

2.3 4.4 0.96 1. 92 7. 14

2.9 5.5 1.21 1. 48 5. 42

1.8 3.2 0.75 5. 15 15. 5

3.0 6.0 1.26 1. 64 6. 77

4.0 8.2 1.68 0.92 4.61

4.9 10.5 2.05 0.62 3.46

5.7 12.5 2.39 0.43 2.54

0.42 25.40

0.42 25.64

0.44 26.84

Kt (Nm/A) = 0.47 Ke (V/krpm) = 28.50

Rated Torque (Nm) Stall Current (A) Rated Power (kW) R (ph-ph) (Ohms) L (ph-ph) (mH)

0.48 1.66 0.33 9.6 21.5

0.91 3.33 0.63 3.8 11.1

1.35 4.80 0.99 2.5 8.1

0.9 2.6 0.57 4.5 10.7

1.6 4.7 1.01 1.49 4.73

2.1 6.6 1.32 0.95 3.10

2.6 8.3 1.63 0.65 2.33

1.3 4.9 0.82 2.01 6.41

2.1 9.2 1.32 0.67 3.01

2.8 12.6 1.76 0.35 1.77

C/D

C/D

C/D Consult Drive Centre/Distributor

N/A Not available

The information contained in this specification is for guidance only and does not form part of any contract.

12

For 3 Phase VPWM Drives 200-240Vrms
Stall torque, rated torque and power relate to maximum continuous operation tested in a 20єC ambient at 12kHz drive switching frequency. All other figures relate to a 20єC motor temperature. Maximum intermittent winding temperature is 140єC.

115E2 A 3.5 10.5 14 4.4 9.5 175 0.06 7.80 9.00 B 6.6 19.8 26.4 6.7 11.8 185 0.10 9.70 10.90 C 9.4 28.2 37.6 9.0 14.1 198 0.14 11.60 12.80 D 12.4 37.2 49.6 11.4 16.6 217 0.18 13.50 14.70 E 15.3 45.9 61.2 13.8 18.9 241 0.21 15.40 17.20 A 5.7 17.1 22.8 9.0 23.3 213 0.09 10.00 12.20 B 10.8 32.4 43.2 15.6 29.9 217 0.16 13.30 15.00

142E2 C 15.3 45.9 61.2 22.2 36.5 275 0.23 16.10 17.80 D 19.8 59.4 79.2 28.8 43.1 301 0.30 18.90 19.60 E 23.4 70.2 93.6 35.4 49.7 365 0.35 21.70 23.40 A C/D N/A B 21.8 65.4 N/A 48.7 93.9 240 0.30 25.30 27.30 C C/D N/A

190E2 D 41.1 123.0 N/A 86.4 131.6 242 0.54 33.90 35.90 E C/D N/A F 58.7 176.0 N/A 123.1 168.3 319 0.72 42.50 44.50 G C/D N/A H 73.2 219.0 N/A 161.8 207.0 632 0.99 51.30 53.10

3.2 2.5 0.67 9.09 47.3

6.1 4.8 1.28 2.82 20.6

8.7 6.8 1.82 1.51 13.1

10.8 8.9 2.26 0.99 9.54

14.0 11.0 2.93 0.82 7.86

5.3 4.1 1.11 4.28 33.7

10.3 7.8 2.16 1.33 15.1

14.6 11.0 3.06 0.75 10.3

18.4 14.2 3.85 0.45 6.96

21.3 16.8 4.46 0.32 5.58

C/D

20.0 15.6 4.19 0.50 7.98

C/D

36.9 29.4 7.73 0.15 3.32

C/D

50.4 42.0 10.6 0.10 2.73

C/D

C/D

3.0 3.8 0.94 4.01 20.1

5.5 7.1 1.73 1.30 9.16

8.1 10.2 2.54 0.73 6.07

10.4 13.4 3.27 0.47 4.26

12.6 16.5 3.96 0.37 3.49

4.9 6.2 1.54 1.90 15.0

9.0 11.7 2.83 0.59 6.85

12.2 16.5 3.83 0.31 4.20

15.8 21.3 4.96 0.20 1.94

N/A

C/D

19.2 23.5 6.03 0.25 3.98

C/D

33.0 44.2 10.4 0.08 1.87

C/D

C/D

C/D

N/A

2.5 4.9 1.05 2.62 12.6

4.7 9.2 1.97 0.82 5.48

6.3 13.1 2.64 0.44 3.57

7.5 17.3 3.14 0.29 2.53

C/D

3.6 8.0 1.51 1.20 9.45

7.0 15.0 2.93 0.36 4.08

C/D

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

2.2 7.5 1.38 0.96 4.80

4.0 14.1 2.51 0.30 2.09

C/D

N/A

N/A

2.9 12.2 1.82 0.49 3.96

C/D

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Control Techniques have an ongoing process of development and reser ve the right to change the specification without notice.

13

055-190 Unimotor
Unimotor
t= 100°C winding 40°C maximum ambient
All data subject to +/-10% tolerance

Performance Data

Ser vo motor for 3 Phase VPWM Drives 380-480Vrms

Motor Frame Size (mm) Frame Length Continuous Stall Torque (Nm) Standard (2) Peak Torque selection max (Nm) High (P) Peak Torque selection max (Nm) Standard Inertia (kgcm2) High Inertia (kgcm2) Winding Thermal Time Const. (sec) Maximum Cogging (Nm) Standard motor weight unbraked (kg) Standard motor weight braked (kg) Rated Speed 2000 (rpm)
Kt (Nm/A) = Ke (V/krpm) =

055U2
A 0.72 2.75 N/A 0.12 B 1.40 5.50 N/A 0.23 C 2.11 8.25 N/A 0.34 A 1.2 3.6 6 0.7 1.1 81 0.02 3.60 4.10

075U2
B 2.2 6.6 11 1.2 1.5 74 0.03 4.40 4.90 C 3.1 9.3 15.5 1.6 2.0 94 0.04 5.20 5.70 D 3.9 11.7 19.5 2.0 2.4 100 0.05 6.00 6.50 A 2.3 6.9 10.4 1.8 3.7 172 0.03 5.10 5.70 B 4.3 12.9 19.4 2.9 4.8 168 0.06 6.30 6.90

095U2
C 5.9 17.7 26.6 4.0 5.9 183 0.08 7.50 8.70 D 7.5 22.5 33.8 5.1 7.0 221 0.10 8.70 9.30 E 9.0 27.0 40.5 6.2 8.1 228 0.13 9.90 10.50

0.03 1.20 1.60

0.05 1.50 1.90

0.07 1.80 2.20

Kt (Nm/A) = 2.40 Ke (V/krpm) = 147.00

Rated Torque (Nm) Stall Current (A) Rated Power(kW) R (ph-ph) (Ohms) L (ph-ph) (mH) Rated Speed 3000 (rpm)
Kt (Nm/A) = Ke (V/krpm) =

C/D

C/D

C/D

1.1 0.5 0.23 144 214

2.1 1.0 0.44 48.2 99.2

3.0 1.3 0.63 25.0 59.2

3.8 1.7 0.80 15.7 44.7

2.2 1.0 0.46 59.0 131

4.0 1.8 0.84 17.0 54.5

5.5 2.5 1.15 9.90 36.5

6.9 3.2 1.45 6.00 25.6

8.2 3.8 1.72 4.30 18.9

0.74 45.00

1.48 89.50

1.58 95.70

Kt (Nm/A) = 1.60 Ke (V/krpm) = 98.00

Rated Torque (Nm) Stall Current (A) Rated Power(kW) R (ph-ph) (Ohms) L (ph-ph) (mH) Rated Speed 4000 (rpm)
Kt (Nm/A) = Ke (V/krpm) =

0.60 0.98 0.21 30.0 67.3

1.20 0.95 0.43 46.0 132.3

1.80 1.34 0.64 32.0 103.0

1.1 0.8 0.35 60.8 98.4

2.0 1.4 0.63 20.1 41.8

2.8 2.0 0.88 10.5 27.6

3.5 2.5 1.10 7.5 19.7

2.0 1.5 0.63 24.5 57.9

3.9 2.7 1.23 6.80 24.3

5.4 3.7 1.70 4.00 15.5

6.8 4.7 2.14 2.50 10.9

8.1 5.7 2.54 2.00 8.50

Kt (Nm/A) = 1.20 Ke (V/krpm) = 73.50

Rated Torque (Nm) Stall Current (A) Rated Power(kW) R (ph-ph) (Ohms) L (ph-ph) (mH) Rated Speed 6000 (rpm)
Kt (Nm/A) = Ke (V/krpm) =

C/D

C/D

C/D

1.0 1.0 0.42 36. 8 54.9

1.7 1.9 0.71 10. 5 24.8

2.3 2.6 0.96 6. 30 14.9

2.9 3.3 1.21 4. 20 10.8

1.8 2.0 0.75 12. 7 31.5

3.0 3.6 1.26 4. 08 13.6

4.0 5.0 1.68 2.10 8.50

4.9 6.3 2.05 1.50 6.30

5.7 7.5 2.39 1.03 4.80

0.74 45.00

0.73 44.30

0.79 47.90

Kt (Nm/A) = 0.80 Ke (V/krpm) = 49.00

Rated Torque (Nm) Stall Current (A) Rated Power(kW) R (ph-ph) (Ohms) L (ph-ph) (mH)

0.48 0.98 0.33 30.0 67.3

0.91 1.91 0.63 11.4 33.1

1.35 2.68 0.99 8.0 25.7

0.9 1.5 0.57 15.0 24.0

1.6 2.8 1.01 5.00 10.6

2.1 3.9 1.32 2.66 6.80

2.6 4.9 1.63 1.90 4.80

1.3 2.9 0.82 5.45 14.1

2.1 5.4 1.32 1.82 6.00

2.8 7.4 1.76 1.05 3.80

C/D

C/D

C/D Consult Drive Centre/Distributor

N/A Not available

The information contained in this specification is for guidance only and does not form part of any contract.

14

Ser vo motor for 3 Phase VPWM Drives 380-480Vrms
Stall torque, rated torque and power relate to maximum continuous operation tested in a 20єC ambient at 12kHz drive switching frequency. All other figures relate to a 20єC motor temperature. Maximum intermittent winding temperature is 140єC.

115U2
A 3.5 10.5 14 4.4 9.5 175 0.06 7.80 9.00 B 6.6 19.8 26.4 6.7 11.8 185 0.10 9.70 10.90 C 9.4 28.2 37.6 9.0 14.1 198 0.14 11.60 12.80 D 12.4 37.2 49.6 11.4 16.6 217 0.18 13.50 14.70 E 15.3 45.9 61.2 13.8 18.9 241 0.21 15.40 17.20 A 5.7 17.1 22.8 9.0 23.3 213 0.09 10.00 12.20 B 10.8 32.4 43.2 15.6 29.9 217 0.16 13.30 15.00

142U2
C 15.3 45.9 61.2 22.2 36.5 275 0.23 16.10 17.80 D 19.8 59.4 79.2 28.8 43.1 301 0.30 18.90 19.60 E 23.4 70.2 93.6 35.4 49.7 365 0.35 21.70 23.40 A 9.6 28.8 N/A 29.9 75.1 217 0.12 21.00 23.00 B 21.8 65.4 N/A 48.7 93.9 240 0.30 25.30 27.30 C 31.1 93.3 N/A 67.5 112.7 241 0.40 29.60 31.60

190U2
D 41.1 123 N/A 86.4 131.6 242 0.54 33.90 35.90 E 50.6 151.6 N/A 105.0 150.2 281 0.66 38.20 40.20 F 58.7 176 N/A 123.1 168.3 319 0.72 42.50 44.50 G 66.0 198.0 N/A 142.9 188.1 476 0.86 46.80 48.80 H 73.2 219 N/A 161.8 207 632 0.99 51.30 53.10

3.2 1.5 0.67 27.8 94.6

6.1 2.8 1.28 8.55 40.5

8.7 4.0 1.82 4.55 25.7

10.8 5.2 2.26 2.96 18.6

14.0 6.4 2.93 2.17 14.7

5.3 2.4 1.11 12.5 58.0

10.3 4.5 2.16 3.60 29.8

14.6 6.4 3.06 2.10 18.7

18.4 8.3 3.85 1.35 13.6

21.3 9.8 4.46 0.98 10.7

9.3 4.0 1.90 6.15 52.90

20.0 9.1 4.19 1.80 28.10

28.4 13.0 5.90 0.83 15.00

36.9 17.2 7.73 0.56 13.0

43.8 21.1 9.20 0.39 8.68

50.4 24.5 10.6 0.33 8.90

53.0 27.5 11.1 0.30 6.73

54.7 30.5 11.5 0.23 6.30

3.0 2.2 0.94 12.6 43.1

5.5 4.2 1.73 3.86 18.6

8.1 5.9 2.54 2.02 11.4

10.4 7.8 3.27 1.40 8.60

12.6 9.6 3.96 1.10 7.40

4.9 3.6 1.54 5.63 31.0

9.0 6.8 2.83 1.72 13.3

12.2 9.6 3.83 0.94 8.30

15.8 12.4 4.96 0.61 6.10

18.0 14.7 5.65 0.44 4.80

8.7 6.0 2.73 2.73 23.50

19.2 13.7 6.03 0.79 13.20

25.0 19.4 7.85 0.41 7.35

33.0 25.7 10.4 0.30 6.11

34.0 31.6 10.7 0.17 3.86

35.0 36.7 11.0 0.14 3.60

36.0 41.3 11.3 0.13 2.99

36.8 45.8 11.6 0.09 2.46

2.5 3.0 1.05 6.91 23.5

4.7 5.5 1.97 2.14 10.2

6.3 7.9 2.64 1.16 6.60

7.5 10.4 3.14 0.73 4.70

8.7 12.8 3.64 0.57 3.90

3.6 4.8 1.51 3.12 17.6

7.0 9.0 2.93 1.00 7.50

8.9 12.8 3.73 0.53 4.70

10.7 16.5 4.48 0.35 3.60

12.2 19.5 5.11 0.24 2. 70

C/D

C/D

C/D

C/D

N/A

N/A

N/A

N/A

2.2 4.4 1.38 3.10 15.5

4.0 8.3 2.51 0.97 4.81

C/D

C/D

N/A

2.9 7.2 1.82 1.42 7.72

4.5 13.5 2.83 0.46 3.44

C/D

C/D

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Control Techniques have an ongoing process of development and reser ve the right to change the specification without notice.

15

055-190 Unimotor
Peak Torque Information

Product Data

Peak Torque defined for a maximum period of 250 ms, RMS 3000 rpm, Tmax = 100°C, 40°C ambient. SC = Stall Current

Peak Torque defined for a maximum period of 250 ms, RMS 3000 rpm, Tmax = 100°C, 40°C ambient. SC = Stall Current 16

Motor Specification Low Voltage Directive 2006/95/EC
Note: Machinery Directive 89/392/EEC amended to 98/37/EC Low Voltage Directive 73/23/EEC superseded by directive 2006/95/EC on 16/01/07, which specifically excludes electric motors. EN 60034 EN 60034-1 General requirements for rotating electrical machiner y Duty: S1 Continuous Storage: -15єC to +40єC Operating: Min ambient 0єC; max ambient 40єC Less than 1000M altitude Relative humidity: 90% non condensing Degree of Ingress protection: IP65 (when mounted and connected) Method of cooling: free circulation, free convection Flange mounted: horizontally or vertically Terminal markings: U V W, Thermal protection: PTC thermistor, 145єC on 075-190 motors Thermal protection: PTC thermistor, 150єC on 055 motors Insulation system: Class F 600V, UL number E214439 on 075-190 motors Insulation system: Class F 600V, on 055 motors The design and performance of motors specifically designed for converter supply Dimensions and output for rotating electrical machines Type N (Customer variants) Balancing: to G6.3, (ISO8821 half key convention)

EN 60034-5 EN 60034-6 EN 60034-7 EN 60034-8 EN 60034-11 EN 60034-18 EN 60034-25 EN 60072 EN 60072-1 ISO1940-1

Standard equipment is not deemed suitable for use in an explosive atmosphere. This product has been designed to be operated with Control Techniques Ser vo drives and must not be put into ser vice unless the machinery into which it is to be incorporated has been declared in conformity with the provisions of the machinery directive.

Standard Brake Specification
Motor Frame Size 055 075 095 115 142 190(A-D) 190(E-H) Supply Volts VDC 24 24 24 24 24 24 24 Input Power Watts 6.3 6.3 16 16 19.5 25 25 Static Torque Standard brake (01) Nm 1.8 2 11 11 18 38 60 High energy brake (05) Nm N/A 2.2 12.2 12.2 22 42 67 Release Time ms nom 22 22 60 60 75 95 120 Moment of Inertia kgcm2 * 0.03 0.07 0.39 0.44 0.54 3.07 4.95 Backlash Degrees** 0.75 1.03 0.94 0.56 0.56 0.77 0.77

*Note 1 kgcm2 = 1x10-4kgm2 **Backlash figure will increase with time

· The brakes are intended for parking duty and are not for dynamic or safety use. · The brake will engage when power is removed. · Refer to your Drive Centre or Distributor if your application requires dynamic braking in emergency conditions. · To provide protection to the brake control circuit it is recommended that a diode is connected across the output terminals of the solid state or relay contacts devices. · Larger torque brakes are available as an option. Please contact your Drive Centre or Distributor for details. · Figures are shown at 20°C brake temperature. Apply the de rate factor of 0.7 to the standard brake torque figures if motor temperature is above 100°C. The de rate factor does not apply to the High energy brake. 17

055-190 Unimotor
Cable Information
PS
Cable Type: PS = Power (Standard) PB= Power (with brake)

Product Data
A 015
Cable Length (metres):
Min - 002 (2 metres) Max - 100

B
Jacket: B = PUR

A
Phase G= A= B= C* = D* = E* =

A
& Earth: Conductor Size 1.5mm2 16A 2.5mm2 22A 4.0mm2 30A 6.0mm2 39A 10.0mm2 53A 16.0mm2 70A

**Ring terminals for Drive studs only

Connection Details Drive End: A = Unidrive (Size 1-2) Ferrules B = Unidrive (Size 3-4) Ring terminals C = 6 way power extension connector (055-142 male pins) F = Unidrive SP (1-2) Ferrules G = Unidrive SP (3-4) Ring terminals H = Digitax ST and SP0 X = Cut end

Connection Details Motor End: A = 055-142 power connector B = 190 power connector X = Cut end

Cable type - PS for motor without brakes, PB for motors with brake. Jacket - B is for a PUR sheath and is the standard selection. Conductor size - Select the conductor size according to the motors STALL CURRENT. Cables of 6mm2 and above will be fitted with ring terminals only. Ratings are for individual cables (not lashed together) in free air temperature up to 40єC - make allowances as appropriate. Connection detail drive end - Select the correct drive end connection for the drive in use. Connection detail motor end - Select the correct motor end connection for the motor in use. Length - Numbers represent the required cable length in metres.

SI
Cable Type: SI = Incremental Encoder SR = Resolver SS = Sin/Cos Encoder

B
Jacket: B = PUR

A
Special Options: A = Standard cable E = Twisted screened SS cable L = 8.5mm dia SI cable

A

A

015
Cable Length (metres):
Min = 002 (2 metres) Max = 100* 10m for SIBL

Connection Details Drive End: A = Digitax ST/Unidrive/Epsilon EP Encoder 15 pin connector B = Unidrive Resolver / Sin/Cos Ferrules F = Epsilon Encoder 26 pin connector G = 17 way extension Encoder male pins H = Unidrive SP Sin/Cos 15 pin connector X = Cut end
*100m on incremental only if +5V tolerance can be maintained

Connection Details Motor End: A= Encoder connector B= Resolver connector C= Sin/Cos connector (Sick|Stegmann) E = 17 way extension Encoder connector F = 90є Encoder connector G = 90є Resolver connector H = 90є Sin/Cos connector (Sick|Stegmann) N= Sin/Cos connector (Heidenhain) O = 90є Sin/Cos connector (Heidenhain) X = Cut end

Cable type Jacket Special options Connection detail drive end Connection detail motor end Length 18

-

Choose the cable type to match the feedback device. B is for a PUR sheath and is the standard selection. A is for standard cable. L is for the low cost 8.5mm incremental cable. Select the correct drive end connection for the drive in use. Select the correct motor end connection for the motor feedback device in use. Numbers represent the required cable length in metres.

Motor connector details Power Plug

055-142 with brake
Pin 1 2 3 4 5 6 Shell Function Phase U (R) Phase V (S) Earth Phase W (T) Brake Brake Screen

055-142 without brake
Function Phase U (R) Phase V (S) Earth Phase W (T) Pin U V W + Shell
¤

190 with brake
Function Phase U (R) Phase V (S) Earth Phase W (T) Brake Brake Screen

190 without brake
Function Phase U (R) Phase V (S) Earth Phase W (T)

Screen

Screen

Signal Plugs

Incremental Encoder
(KP, MP, CP, CA, MA)

Pin
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Body

Function
Thermistor Thermistor S1 S1 Inverse S2 S2 Inverse S3 S3 Inverse Channel A Index Index Inverse Channel A Inverse Channel B Channel B Inverse +5V 0 Volts Screen

Heidenhain Sin/Cos Encoders (EM, FM, EC, FC, EB, FB) Function
Thermistor Thermistor Screen (Optical encoder only)

Resolver
(AE, AR)

Function
Excitation high Excitation low Cos high Cos low Sin high Sin low Thermistor Thermistor

Sick|Stegmann Sin/Cos Encoders (TL, UL, RB, SB) Function
REF Cos +Daten -Daten +Cos +Sin REF Sin Thermistor Thermistor Screen 0 Volts +Volts

+ Clock - Clock + Cos +Data - Data - Cos + Sin - Sin + 8V 0 Volts Screen

Screen

19

DRIVING THE WORLD...
AUSTRALIA Melbourne Application Centre T: +613 973 81777 info.au@controltechniques.com Sydney Drive Centre T: +61 2 9838 7222 info.au@controltechniques.com AUSTRIA Linz Drive Centre T: +43 7229 789480 info.at@controltechniques.com BELGIUM Brussels Drive Centre T: +32 1574 0700 info.be@controltechniques.com BRAZIL Brazil Sales Office T: +55 15 3238 3605 info.br@controltechniques.com CANADA Toronto Drive Centre T: +1 905 201 4699 info.ca@controltechniques.com Calgary Drive Centre T: +1 403 253 8738 info.ca@controltechniques.com CHINA Shanghai Drive Centre T: +86 21 5426 0668 info.cn@controltechniques.com Beijing Application Centre T: +86 10 856 31122 ext 820 info.cn@controltechniques.com CZECH REPUBLIC Brno Drive Centre T: +420 541 192111 info.cz@controltechniques.com DENMARK Copenhagen Drive Centre T: +45 4369 6100 info.dk@controltechniques.com FRANCE* AngoulЙme Drive Centre T: +33 5 4564 5454 info.fr@controltechniques.com GERMANY Bonn Drive Centre T: +49 2242 8770 info.de@controltechniques.com Chemnitz Drive Centre T: +49 3722 52030 info.de@controltechniques.com Darmstadt Drive Centre T: +49 6251 17700 info.de@controltechniques.com GREECE* Athens Application Centre T: +0030 210 57 86086/088 info.gr@controltechniques.com HOLLAND Rotterdam Drive Centre T: +31 184 420555 info.nl@controltechniques.com HONG KONG Hong Kong Application Centre T: +852 2979 5271 info.hk@controltechniques.com INDIA Chennai Drive Centre T: +91 44 2496 1123/ 2496 1130/2496 1083 info.in@controltechniques.com Pune Application Centre T: +91 20 2612 7956/2612 8415 info.in@controltechniques.com Kolkata Application Centre T: +91 33 2357 5302/2357 5306 info.in@controltechniques.com New Delhi Application Centre T: +91 11 2 576 4782/2 581 3166 info.in@controltechniques.com

.......... .......... ..........
IRELAND Newbridge Drive Centre T: +353 45 448200 info.ie@controltechniques.com ITALY Milan Drive Centre T: +39 02575 751 info.it@controltechniques.com Reggio Emilia Application Centre T: +39 02575 751 info.it@controltechniques.com Vicenza Drive Centre T: +39 0444 933400 info.it@controltechniques.com KOREA Seoul Application Centre T: +82 2 3483 1605 info.kr@controltechniques.com MALAYSIA Kuala Lumpur Drive Centre T: +603 5634 9776 info.my@controltechniques.com REPUBLIC OF SOUTH AFRICA Johannesburg Drive Centre T: +27 11 462 1740 info.za@controltechniques.com Cape Town Application Centre T: +27 21 556 0245 info.za@controltechniques.com RUSSIA Moscow Application Centre T: +7 495 981 9811 info.ru@controltechniques.com SINGAPORE Singapore Drive Centre T: +65 6468 8979 info.sg@controltechniques.com SLOVAKIA EMERSON A.S T: +421 32 7700 369 info.sk@controltechniques.com SPAIN Barcelona Drive Centre T: +34 93 680 1661 info.es@controltechniques.com Bilbao Application Centre T: +34 94 620 3646 info.es@controltechniques.com Valencia Drive Centre T: +34 96 154 2900 info.es@controltechniques.com SWEDEN* Stockholm Application Centre T: +468 554 241 00 info.se@controltechniques.com SWITZERLAND Lausanne Application Centre T: +41 21 637 7070 info.ch@controltechniques.com Zurich Drive Centre T: +41 56 201 4242 info.ch@controltechniques.com TAIWAN Taipei Application Centre T: +886 22325 9555 info.tw@controltechniques.com THAILAND Bangkok Drive Centre T: +66 2962 2092 99 info.th@controltechniques.com TURKEY Istanbul Drive Centre T: +90 216 4182420 info.tr@controltechniques.com UAE* Dubai Application Centre T: +971 4 883 8650 info.ae@controltechniques.com UNITED KINGDOM Telford Drive Centre T: +44 1952 213700 info.gb@controltechniques.com USA California Drive Centre T: +1 562 943 0300 info.us@controltechniques.com Charlotte Application Centre T: +1 704 393 3366 info.us@controltechniques.com Chicago Application Centre T: +1 630 752 9090 info.us@controltechniques.com Cleveland Drive Centre T: +1 440 717 0123 info.us@controltechniques.com Florida Drive Centre T: +1 239 693 7200 info.us@controltechniques.com Latin America Sales Office T: +1 305 818 8897 info.us@controltechniques.com Minneapolis US Headquarters T: +1 952 995 8000 info.us@controltechniques.com Oregon Drive Centre T: +1 503 266 2094 info.us@controltechniques.com Providence Drive Centre T: +1 401 541 7277 info.us@controltechniques.com Utah Drive Centre T: +1 801 566 5521 info.us@controltechniques.com

Control Techniques Drive & Application Centres

Control Techniques Distributors
ARGENTINA Euro Techniques SA T: +54 11 4331 7820 eurotech@eurotechsa.com.ar BAHRAIN Iftikhar Electrical Est. T: +973 271 116 ieepower@batelco.com.bh BULGARIA BLS - Automation Ltd T: +359 32 968 007 info@blsautomation.com CROATIA Koncar MES d.d. T: +385 1 366 7273 nabava@koncar-mes.hr CYPRUS Acme Industrial Electronic Services Ltd T: +3572 5 332181 acme@cytanet.com.cy EGYPT Samiram T: +202 7360849/ +202 7603877 samiramz@samiram.com INDONESIA Pt Apikon Indonesia T: +65 6468 8979 info.my@controltechniques.com LEBANON Black Box Automation & Control T: +961 1 443773 info@blackboxcontrol.com PHILIPPINES Control Techniques Singapore Ltd T: +65 6468 8979 info.my@controltechniques.com POLAND APATOR CONTROL Sp. z o.o T: +48 56 6191 207 drives@apator.torun.pl PORTUGAL Harker Sumner S.A T: +351 22 947 8090 drives.automation@harker.pt PUERTO RICO Powermotion T: +1 787 843 3648 dennis@powermotionpr.com QATAR AFI Sitna Technologies T: +974 468 4442 jp33@qatar.net.qa SAUDI ARABIA A. Abunayyan Electric Corp. T: +9661 477 9111 aec-salesmarketing@ abunayyangroup.com SERBIA & MONTENEGRO Master Inzenjering d.o.o T: +381 24 551 605 master@eunet.yu SLOVENIA PS Logatec T: +386 1 750 8510 ps-log@ps-log.si TUNISIA SIA Ben Djemaa & CIE T: +216 1 332 923 bendjemaa@planet.tn URUGUAY Secoin S.A T: +5982 2093815 secoin@adinet.com.uy VENEZUELA Digimex Sistemas C.A. T: +58 243 551 1634 VIETNAM N.Duc Thinh T: +84 8 9490633 infotech@nducthinh.com.vn

Pt Yua Esa Sempurna Sejahtera LITHUANIA Elinta UAB T: +65 6468 8979 info.my@controltechniques.com T: +370 37 351 987 sigitas@elinta.lt ISRAEL Dor Drives Systems Ltd T: +972 3900 7595 info@dor1.co.il KENYA Kassam & Bros Co. Ltd T: +254 2 556 418 kassambros@africaonline.co.ke KUWAIT Saleh Jamal & Company WLL T: +965 483 2358 sjceng@almullagroup.com LATVIA EMT T: +371 760 2026 janis@emt.lv MALTA Mekanika Limited T: +35621 442 039 mfrancica@gasan.com MEXICO MELCSA T: +52 55 5561 1312 melcsamx@iserve.net.mx SERVITECK, S.A de C.V T: +52 55 5398 9591 servitek@data.net.mx MOROCCO Leroy Somer Maroc T: +212 22 354948 Ismaroc@wanadoopro.ma NEW ZEALAND Advanced Motor Control. Ph. T: +64 (0) 274 363 067 info.au@controltechniques.com

CENTRAL AMERICA Mercado Industrial Inc. FINLAND T: +1 305 854 9515 SKS Control rsaybe@mercadoindustrialinc.com T: +358 207 6461 control@sks.fi CHILE IngenierМa Y Desarrollo HUNGARY TecnolСgico S.A Control-VH Kft T: +56 2741 9624 T: +361 431 1160 idt@idt.cl info@controlvh.hu COLOMBIA Sistronic LTDA T: +57 2 555 60 00 sistronic@telesat.com.co ICELAND Samey ehf T: +354 510 5200 samey@samey.is

© Control Techniques 2008. The information contained in this brochure is for guidance only and does not form part of any contract.The accuracy cannot be guaranteed as Control Techniques have an ongoing process of development and reserve the right to change the specification of their products without notice.

* Operated by sister company

PN. 0702-0000-02 04/08 .