usrp
dec 15
Intro:
We have 2 N210 usrps. One with a sbx daughter
board and a second with a wbx daughter board.
We are using the wbx daughter board to take plasma line data
for aeronomy (using juha's software).
Devices:
name
|
mother board
|
Rx daughter board
|
|
Name
|
serial# |
ipAdr |
macAdr |
Freq
Mhz
|
Name
|
freq Range
Mhz
|
Gain
|
Notes
|
usrp2
|
N210r4
|
F4A7C3
|
192.168.10.2
|
00:80:2f:0a:e7:f2
|
-50 to 50
|
SBXv3 RX
|
400 to
4400
|
0,.0-31.5
.5db step
|
IQ
no lo offset
|
usrp2
|
N210r4
|
F4A737
|
192.168.10.3
|
00:80:2f:0a:e7:d5
|
-50 to 50
|
WBXv3 RX+GDB
$480
|
68.75 to
2200
|
0,.0-31.5
.5db step |
IQ
no lo offset
|
- Use uhd_find_devices to get devices
- use uhd_usrp_probe --args addr=ipadr to probe each
device.
- Note: We are currently using
the 2nd usrp with the wbx daughter board for plasma line
observations.
usrp2/n210 specs
- external pps reference
- external 10Mhz reference
- fixed 100Mhz clock rate
- 100Ms/s dual adc.
- fpga:
- xilinx spartan 3a dsp 3400 fpga
- 2 rx DDC chains in fpga
- 16 bit and 8 bit sample modes (sc8 and sc16)
- Up to 25 Mhz or rf bandwidth with 16 bit samples
- Up to 50 Mhz of rf bandwidth with 8 bit samples
- LED'S:
- A: transmitting
- B: mimo cable link
- C: receiving
- D:firmware loaded
- E: reference lock
- F: cpld loaded
- Ref Clock 10Mhz
- usrp2: 5 to 15dbm
- N210: 0 to 15 dbm
- PPS:
- usrp2: 5V pp
- N210: 3.3 to 5V pp
- Only 1 daughter board slot.
- WBX Daugherboard
- 5db noise figure
- 2 quadratrure frontends (1 transmit, 1 rcv)
- Defaults to direct conversion.
- Can be used in low IF mode through lo_offset with
uhd:tune_request_t
- receive lo. can be set to integer=N tuning for better spur
performance.
- rcv antennas: tx/rx or rx2
- Bandwidth: 40 Mhz rx & tx
- SBX Daugtherboard
- 2 quadratrure frontends (1 transmit, 1 rcv)
- Defaults to direct conversion.
- Can be used in low IF mode through lo_offset with
uhd:tune_request_t
- receive lo. can be set to integer=N tuning for better spur
performance.
- rcv antennas: tx/rx or rx2
- Bandwidth: 40 Mhz rx & tx
- LEDs
- All flash when daughterboard is initialized
- TX LD: transmit synth lock detect
- TX/RX: receiver on Tx/Tx antenna port (no TX)
- RX ld: receive synth lock detect
- RX1/RX2: receiver on RX2 antenna port
- Tuning
- usrp has 2 tuning stages:
- rf frontend goes rf to if (daughter board)
- DSP: goes IF to bandband (mother board)
- After tuning, check for lo's locked.. or wait for up to a
second.
Documentation:
Measurements (in date order):
<-
page up
home_~phil