GALFA Spectrometer Jumper Settings

Документ взят из кэша поисковой машины. Адрес оригинального документа : http://www.naic.edu/alfa/galfa/docs/galspect/spectrometer/jumpers.html
Дата изменения: Mon Oct 4 23:19:44 2004
Дата индексирования: Sun Dec 23 06:23:25 2007
Кодировка:

GALFA Spectrometer Board Jumper Settings

Jumper placement diagram (pdf)
Jumper listing
Jumper settings for cPCI operations

Jumper listing

Power

J9: +1.5V regulator control
- Jumper 1 to 3 (m_dn) to set +1.5V regulator (U4) output to -5% nominal (+1.425V)
- Jumper 2 to 4 (m_up) to set +1.5V regulator (U4) output to +5% nominal (+1.575V)
J10: +1.5V connection
- Jumper 1 to 3 to provide +1.5V to FPGAs from switching regulator U4
- Jumper 2 to 4 to provide +1.5V to FPGAs from switching regulator U4
J21: +1.5V connection
- Jumper 1 to 3 to provide +1.5V to FPGAs from switching regulator U4
- Jumper 2 to 4 to provide +1.5V to FPGAs from switching regulator U4
J11: +2.5V regulator control
- Jumper 1 to 3 (m_dn) to set +2.5V regulator (U6) output to -5% nominal (+2.375V)
- Jumper 2 to 4 (m_up) to set +2.5V regulator (U6) output to +5% nominal (+2.625V)
J12: +2.5V connection
- Jumper 1 to 3 to provide +2.5V to FPGAs from DC switching regulator U6
- Jumper 2 to 4 to provide +2.5V to FPGAs from DC switching regulator U6
J20: +2.5V connection
- Jumper 1 to 3 to provide +2.5V to FPGAs from switching regulator U6
- Jumper 2 to 4 to provide +2.5V to FPGAs from switching regulator U6
J16: -3V connection
- Jumper 1 to 3 to provide -3V to ADCs from linear regulator U8
- Jumper 2 to 4 to provide -3V to ADCs from linear regulator U8
J17: +3V connection
- Jumper 1 to 3 to provide +3V to ADCs from linear regulator U9
- Jumper 2 to 4 to provide +3V to ADCs from linear regulator U9

Clocking

J2: Clock Source
- Jumper 1 to 3 (xtal) to use on-board crystal oscillator in socket U1
- Jumper 2 to 4 (xtern) to use external clock received through RJ45 J1
J5: SYNC
- Jumper 1 to 3 to drive SYNC_OUT directly from SYNC_IN
- Jumper 2 to 4 to generate SYNC_OUT from 2V4000/2V6000 FPGA
J6: XTRA
- Jumper 1 to 3 to drive XTRA_OUT directly from XTRA_IN
- Jumper 2 to 4 to generate XTRA_OUT from 2V4000/2V6000 FPGA
J7: 1PPS
- Jumper 1 to 3 to drive 1PPS_OUT directly from 1PPS_IN
- Jumper 2 to 4 to generate 1PPS_OUT from 2V4000/2V6000 FPGA
J8: CLK
- Jumper 1 to 3 to drive CLK_OUT directly from CLK_IN
- Jumper 2 to 4 to generate CLK_OUT from 2V4000/2V6000 FPGA

Compact PCI Interface

J19: cPCI Interface Clock
- Jumper 1 to 2 to enable 66MHz interface

FPGA Configuration

JP1: 2V4000/2V6000
- Jumper 1 to 2 to ground programming mode pin M0
- Jumper 3 to 4 to ground programming mode pin M1
- Jumper 5 to 6 to ground programming mode pin M2
JP2: 2V1000
- Jumper 1 to 2 to ground programming mode pin M0
- Jumper 3 to 4 to ground programming mode pin M1
- Jumper 5 to 6 to ground programming mode pin M2

(From Xilinx Virtex-II Platform FPGA Handbook)

Configuration Mode	M2	M1	M0
Master Serial	0	0	0
Slave Serial	1	1	1
Master SelectMAP	0	1	1
Slave SelectMAP	1	1	0
Boundary Scan	1	0	1

Jumper settings for normal (cPCI) operations

Leave the following jumpers UNCAPPED:

J5
J6
J7
J8
J9
J11
J19
JP1
Remove crystal oscillator from U1

INSTALL the following jumpers:

J2, connect 2 to 4
J10, 2 jumpers (1 to 3, 2 to 4)
J21, 2 jumpers (1 to 3, 2 to 4)
J12, 2 jumpers (1 to 3, 2 to 4)
J20, 2 jumpers (1 to 3, 2 to 4)
J16, 2 jumpers (1 to 3, 2 to 4)
J17, 2 jumpers (1 to 3, 2 to 4)
JP2, 3 jumpers (1 to 2, 3 to 4, 5 to 6)