XMM-Newton Science Analysis System . ... yes . ... pn source region expression for spectral analysis . ... pn background region expression for spectral analysis . ... mos1 source region expression for spectral analysis . ... mos1 background region expression for spectral analysis . ... mos2 source region expression for spectral analysis . ... pn source region expression for timing analysis . ... mos1 source region expression for timing analysis . ... mos2 source region expression for timing analysis . ...

... Публикации и издания Публикации профессорско-преподавательского состава СГАУ Издания проф. Сосниной Т.Н. Biosphere: Analysis of Value Parameters . ... Besides, the ways of saving the use value and value properties of biosphere are analyzed. The expediency of transformation of two-criterion theory of value into the three- criterion theory of the balance of value, where the ecologic component performs the function of the key criterion has been founded. ... BIOSPHERE USE VALUE OF THE PRODUCT: MAIN . ...

... The Earth orientation parameters UT1 and polar motion (x pol ; y pol ) are relat­ ed with the values of UT0 and VOL obtained from the LLR analysis for a station with geocentric longitude and latitude (–; OE) by the following expression: 7 UT0 \Gamma UTC = UT1 \Gamma UTC + (x pol sin – + y pol cos –) tan OE 15 V OL = x pol cos – \Gamma y pol sin – At least four normal points for each station--reflector pair at one day were accepted for the diurnal UT0 estimations. ...

... We demonstrate through numerical simulations that model parameters estimated with our technique are essentially bias-free, even when the average number of counts per bin is 1. ... The IW technique avoids such biases by estimating through successive iterations, where for each iteration, j, , and the best-fit parameters are determined by minimization of . ... In our sample, we find that the minimum values and best-fit parameters converge after about 6 iterations. ...

... ACQ-DIST Optional Parameter for FGS 1 , 2 . ACQTYPE Optional Parameter for STIS . Acquisition modes . ... Aperture Coordinate System . ... AFTER date Special Requirement . ... BINAXIS1, BINAXIS2 Optional Parameters for STIS 1 , 2 . ... BUFFER-TIME Optional Parameter for STIS . ... CHECKBOX Optional Parameter for STIS . ... Calibration Targets . ... CR-SPLIT Optional Parameter for STIS . ... DIFFUSE-CENTER Optional Parameter for STIS . ... GAIN Optional Parameter for STIS . ... Position . ...

The position of the objects on the sky were generally measured to a precision between 1 and 4 arcsec. ... For the stars, the position is always at epoch 2000, whatever J2000 or B1950 coordinates are printed. ... The celestial position is given as coordinates in 4 different systems: . ... B1950 . ... Galactic coordinates in the reference frame called "new" system, adopted by IAU in 1958. Galactic pole at B124900.0+272400, node at ra=282.25,l=33 deg (inclination 62.6 deg). ... 1 arcsec . ...

... This section will deal with obtaining photons within specified regions of an image. Available regions are: Annulus Box Circle Ellipse Field -- entire field Irregular region based on intensity of map... i.e. region defined by contour levels. ... The imcnts task in the xray-spatial package sums the source and background counts in specified regions, and subtracts one from the other properly normalized. ... imcnts* - Find counts in an extended region, after removing an embedded point source . ...

... We assume that an instantaneous starburst occured in the region of the Galactic center, with half of the stars (in number) being formed in binaries. The total mass of the stars formed during the starburst was taken to be , as indicated by the Tamblyn & Rieke (1993) analysis. ... In fact, the number of stars in IRS 16 estimated by Tamblyn & Rieke (1993) is uncertain within a factor of 2, but this is actually of no importance as long as we only use relative numbers of different X-ray source species. ...

The determination of the detector parameters is based on sets of images of a spatially uniform-illumination scene (flatfield frames) and without any illumination (dark frames), putting a plug in place of the filter, taken at a series of exposure times. ... We interleave before and after each exposure time in the series of flatfield frames a set of reference images at an exposure time of 1 sec to determine the possible temporal variation of the illumination level. ...

Chair of solid state physics . ... Laboratory practical training on the structural analysis for 3rd year students of the Solid State Physics Chair of MIPT . ... X-ray diffraction methods in materials research . Debye method: determination of lattice parameters, identification of crystal phases . ... X-ray phase analysis: computer processing of X-ray diffraction spectra, identification of crystal phases using ICDD database . ... X-ray powder diffraction: qualitative phase analysis. ...